iFixit - Active Questions With Device "Coffee Maker"

Siemens EQ Series: Süt alırken makina çok ses çıkarıyor

Fri, 26 Dec 2025 02:39:24 -0700

Sütü çekerken çok ses çılarıyor

DeLonghi ECAM Series: Why is the autorinse not starting?

Tue, 30 Jun 2026 14:07:26 -0700

Hi,

My DeLonghi ECAM 220.22 Magnifica Start is stuck during startup. The automatic rinse never starts.

The issue started after making a coffee. About 5 minutes later, i smelled something burning. The machine became very hot and the plastic support around the thermoblock slightly melted (i checked it).

Now:

The machine turns on.
The brew group moves.
The lights keep flashing while waiting for the auto rinse.
No water comes out.

I checked:

Hoses are clean and not kinked.
No visible blockage/limescale in the thermoblock.
Wires/connectors look normal.
When disconnecting the inlet hose to the thermoblock, only a tiny amount of water comes out (when I power it back on).

Thanks!

⟐ Edited by author Haziran 30, 2026 at 14:07 GMT-7

Ninja Coffee Makers: Ninja CE201 size and type of screws on bottom plate

Sat, 27 Jun 2026 10:26:35 -0700

Hi,

I need to open the bottom of my unit so that I can clean or replace the plastic tubing. Does anyone know the type and size of screw for this unit? I've tried all my hex screws, but I apparently don't have the right bit. Thanks.

⟐ Answered Haziran 27, 2026 at 10:26 GMT-7

Nespresso U: The spout is not moving into the correct position

Sat, 27 Jun 2026 01:22:36 -0700

The coffee is going straight into the waste container as opposed to coming out through the spout. It appears that the spout is not dropping down into the correct position. How do you ensure that the spout does drop in the correct position when the mechanism starts?

⟐ Answered Haziran 27, 2026 at 1:22 GMT-7

Mr. Coffee BVMC-SJX33GT: What tools do I need to remove the bottom plate?

Fri, 26 Jun 2026 14:18:48 -0700

What tool is used to remove the bottom plate?

⟐ Answered Haziran 26, 2026 at 14:18 GMT-7

Jura E8: Service manual? Full tear-down?

Fri, 26 Jun 2026 04:43:13 -0700

I am having a hard time finding the service manual for this thing. Has anybody found one or know where I can buy one?

⟐ Commented Haziran 26, 2026 at 4:43 GMT-7

Mr. Coffee BVMC-SJX33GT: Coffee not brewing but light is on.

Thu, 25 Jun 2026 10:46:59 -0700

The brewing light is on but, no sounds or other signs of brewing. Power is good. Need to also know how to check for particle accumulation.

⟐ Answered Haziran 25, 2026 at 10:46 GMT-7

Keurig K55: Why is my Keurig Classic constantly turning off while brewing?

Wed, 24 Jun 2026 03:01:16 -0700

I put the Keurig brand K cup in, pull down the top, and press the brew button. It works for a split second then the machine turns off and I waste a K Cup. The K Cup just leaks into my cup and I have to remove it and try again because if I try and use the same K Cup it doesn’t taste right! It happens with numerous Keurig branded K Cups including Hot Chocolate, Cafe Caramel, and Cafe Vanilla. It’s been happening at least 3-4 times a week.

This is my third machine I’ve received from Keurig support and it’s still happening. I’ve done all the needle cleaning, reseting, descaling, and many other fixes. The unit is not even 3 months old.

I’m just at a loss of what to do because I don’t see many people having the same problem. I’m also sick and tired of wasting perfectly good K Cups! Anybody have ideas how to permanently fix this?

EDIT & SOLUTION: I've been able to resolve the issue using a work around. This is not a fix and I don't know why Keurig hasn't fixed it after years of this happening.

When using a milk based K Cup, press it into the bottom by hand so the K Cup is punctured. Pull it up and rotate 90º and close the lid. This gives the K Cup two holes and much less pressure. It has worked perfectly since I've been doing this.

⟐ Commented Haziran 24, 2026 at 3:01 GMT-7

Hamilton Beach Coffee Maker: Coffee maker is slowly leaking clear water from the bottom.

Tue, 23 Jun 2026 02:44:17 -0700

I believe my Hamilton Beach 12 cup coffee maker 49465R needs a new hose, but where do I get one? The company doesn't sell them, eBay doesn't have any, ifixit doesn't have any. Looking for advice on how to DIY a hose. Is the tubing similar from one coffee maker to another...in other words, could I buy a tube from say DeLonghi and cut it to fit?

⟐ Edited Haziran 23, 2026 at 2:44 GMT-7

Krups Nespresso XN 2140: There’s not enough coffee extracted.

Fri, 19 Jun 2026 18:47:05 -0700

There’s not enough coffee extracted.

Keurig 2.0-400: Keurig 2.0 will not dispense water and make cofee

Fri, 19 Jun 2026 04:07:48 -0700

it lights up and sounds like its going to dispense water but only a few drops come out

⟐ Answered Haziran 19, 2026 at 4:07 GMT-7

DeLonghi ESAM Family: Fuse shuts off when I press the power button of my expresso machine

Thu, 18 Jun 2026 01:28:29 -0700

Hi everyone. I got a problem with my Delonghi micalite Expresso Machine. When I press the power button to turn it on the fuse shuts down and if I try again the same thing happens.

I've done this continuity checkup which I found in another post:

"This is usually caused by the heating element rupturing and shorting to the boiler/casing. You can test for this by removing the top/back of the machine (6 small phillips-head screws) and checking for continuity across the heating element contacts (the two 90 degree prongs sticking out of the top of the boiler). If there's no continuity then the boiler needs to be rebuilt with a new heating element and boiler gasket."

The result was .049, which is good I guess. I attached two pictures for you to check if I've tested the right ends.

Anyone know what's the next step to found the problem?

Thank you!

⟐ Answered Haziran 18, 2026 at 1:28 GMT-7

DeLonghi ETAM family: ECAM 450.55 G ELETTA EXPLORE replace Standby-Button

Wed, 17 Jun 2026 14:01:06 -0700

Hi folks,

Does anyone have an idea how I can disassemble the top section of the Eletta Explore?

I need to replace the standby button.

Thanx

Peter

⟐ Commented Haziran 17, 2026 at 14:01 GMT-7

Keurig Elite: My Keurig Will not draw water

Sat, 13 Jun 2026 11:38:29 -0700

My Keurig shows out of water but will not draw water from the reservoir

⟐ Commented Haziran 13, 2026 at 11:38 GMT-7

Keurig K-Duo: Why too much water?

Fri, 12 Jun 2026 13:34:27 -0700

Keurig k-duo essentials new not measuring right amount of water for pot coffee. Always too much.

Bosch Coffee Maker: How to replace a coupling in a Bosch Coffe machine. Milk frother

Wed, 10 Jun 2026 04:16:42 -0700

I bought the part and I need instructions how to repace it Model TES70129RW10 Coupling No. 00647103. a video will be nice.

⟐ Answer accepted Haziran 10, 2026 at 4:16 GMT-7

Jura: Jura Z5 Gen II brew group motor keeps running

Thu, 04 Jun 2026 15:18:51 -0700

The engine that drives the large white gear on the brew group up and down keeps running when the gear is all the way down (obviously accompanied by loud rattling noise).

I disassembled and cleaned the brew group, but it makes no difference. What is used to detect when to stop the motor? I don't see any obvious sensor. Is it simply timed.

Any suggestions how to troubleshoot and hopefully repair?

⟐ Commented Haziran 04, 2026 at 15:18 GMT-7

Keurig K10 MINI PLUS: need a owners manual

Tue, 02 Jun 2026 22:26:54 -0700

owners manual for k10

⟐ Commented Haziran 02, 2026 at 22:26 GMT-7

Ninja Coffee Bar CF086: Drip stop light prevents brewing

Mon, 01 Jun 2026 05:06:48 -0700

I have a ninja coffee bar, had it for 2 years. The drip stop light lit while brewing, and wouldn't brew at all. I replaced the drip tray, and went away with one brew. Light returns. Seems to occur with unbalanced surfaces too, and whenever we slightly move it or shake it, the light MAY go off and brew for a bit. Has anyone taken one apart and disabled the drip stop sensor, and if so, how?

⟐ Commented Haziran 01, 2026 at 5:06 GMT-7

Bravilor Coffee Maker: Bonamat th10 error 12 was tun

Sat, 30 May 2026 01:49:44 -0700

How do i fix error 12 bonamat th10