⟐ Answer edited Haziran 30, 2025 at 5:15 GMT-7

Not: Bilgisayarın tuşları çalışıyor sadece arada bu hatayı yaptığı için sürekli kullanmıyorum.

⟐ Answer accepted Nisan 17, 2024 at 4:41 GMT-7

⟐ Answered Şubat 04, 2024 at 13:24 GMT-7

⟐ Answered Kasım 06, 2023 at 13:26 GMT-7

Cihaz 15-20 dk çalıştıktan sonra bu ekran kayması bitiyor sadece üst kısımda bi kaç çizgi şeklinde bir titretme kalıyor.

Bu sorun neden kaynaklanıyor ? Daha önce böyle bir sorun yaşayan olduysa yardımcı olabilirseniz sevinirim .


Hello, while my laptop was not having any problems, suddenly the screen started to slip.

After the device runs for 15-20 minutes, this screen shift ends, only a few lines remain at the top.

Why does this problem occur? If anyone has had this problem before, I'd appreciate it if you could help.

⟐ Edited by author Mart 25, 2021 at 16:09 GMT-7

⟐ Edited by author Aralık 26, 2020 at 5:04 GMT-7

Merhabalar. Bugün çözüme baştan macOS Catalina yükleyerek ulaştım. Bilgisayar kapalıyken alt+cmd+r tuşlarına basıp bilgisayarı açtım ve Recovery moduna girdi. Diskleri sildim ve cihaz internet üzerinden Catalina yazılımını indirip kurdu. Bilgisayardaki yavaşlık, ısınma gibi problemlerin hepsi çözüldü.

⟐ Answer deleted Aralık 21, 2020 at 16:49 GMT-7

Bilgisayar özellikleri hakkında çok fazla bir bilgim yok ama bazı programları kullanıyorum ve bazılarını öğrenmenmeye çalışıyorum. Sürekli olarak After Effects ve Premiere Pro kullanacağım ve başlangıç seviyesi olarak Cinema 4D. Bu programları kullanmak ve sıkıntısız render almak için aşağıdaki özellikler yeterli mi?

Macbook Pro 13”

• 1.4 GHz 4 çekirdekli 8. nesil Intel Core i5 işlemci, 3.9 GHz’e kadar Turbo Boost
• 16 GB 2133 MHz LPDDR3 bellek
• 256 GB SSD depolama
• True Tone özelliğine sahip Retina ekran
• Intel Iris Plus Graphics 645
• İki adet Thunderbolt 3 bağlantı noktası
• Touch Bar ve Touch ID

⟐ Commented Temmuz 22, 2019 at 17:35 GMT-7

Teşekkürler.

⟐ Answer edited Mart 21, 2019 at 6:32 GMT-7

Bu ne demek???

Bu uyarıyı aldığımda herhangi bir USB takılı değil???

⟐ Answer deleted Eylül 19, 2018 at 13:55 GMT-7

Mac was inside of suitcase and it was inside of a bag.

Mac boots up,I can hear the chime,but the screen is totally black,not even “light” black. Caps lock light doesn’t work.

I tried SMC,PRAM reset, didn’t work.

Reconnecting screen display by unplugging those two things didn’t work. I used this video

Reconnecting battery didn’t work.

I also tried SMC,PRAM reset while the battery was disconnected and Mac was getting energy from the charger. Didn’t work. I used that video.

What else can I do before changing the screen?I don’t want to swap screen cause it’s expensive.

⟐ Commented Temmuz 01, 2026 at 22:25 GMT-7

video of issue

Screen

Display cables

Or logic board issues

⟐ Commented Temmuz 01, 2026 at 20:17 GMT-7

I replaced the battery in my Late 2013 Retina MacBook Pro 15” (A1398, logic board 820-3662-A) using the iFixit guide, which required removing the logic board.

While removing the heat sink, three of the four threaded mounting bosses separated from the logic board and remained attached to the heat sink. The heat sink screws were extremely tight, but I did not use excessive force or power tools.

Photos are attached showing:

• the detached mounting bosses still attached to the heat sink,

• the corresponding locations on the logic board,

• and the overall board.

The board itself does not appear to have torn fiberglass or obvious PCB damage.

The Mac now powers on and reaches the macOS login screen, but after several seconds the fans ramp up steadily and the machine shuts off. Before concluding that this is a thermal issue, I’d like to understand the mechanical failure.

My questions are:

1. On the 820-3662-A board, how are these heat sink mounting bosses originally attached?

2. Is this a known failure mode, or does it suggest the machine was previously repaired?

3. Can the bosses be properly reattached, and if so, what is the correct repair method?

4. If they cannot be repaired reliably, what is the recommended solution?

I’d appreciate hearing from anyone with board-level repair experience on this specific model.

⟐ Commented Temmuz 01, 2026 at 18:08 GMT-7

I have a MacBook Air M1 2020 (A2337) with a keyboard issue. The 3, E, and D keys not work. These three keys are aligned vertically on the keyboard. I want to mention that this is how I purchased the macbook with this problem. I thought I could clean each key individually and solve the problem, but it seems my idea didn't work.

What I have already checked:

• The MacBook has never had any liquid damage.
• I removed the individual keycaps and inspected the mechanisms underneath.
• The rubber domes and key mechanisms look perfectly fine.
• There are no signs of corrosion or dirt.
• I opened the laptop and inspected the inside, which is also very clean.
• I disconnected and reconnected the keyboard flex cable, but the issue remains.
• All other keys on the keyboard work normally.

Since the affected keys are in the same vertical line (3, E, D), I am wondering if this could be a keyboard matrix issue or a failed row/column circuit.

Has anyone experienced the same problem on an A2337 MacBook Air M1? Is there any repair possible without replacing the entire keyboard or top case?

Any advice or schematics would be greatly appreciated.

Thank you!

⟐ Commented Temmuz 01, 2026 at 15:11 GMT-7