⟐ Answer edited Haziran 30, 2025 at 5:15 GMT-7

Not: Bilgisayarın tuşları çalışıyor sadece arada bu hatayı yaptığı için sürekli kullanmıyorum.

⟐ Answer accepted Nisan 17, 2024 at 4:41 GMT-7

⟐ Answered Şubat 04, 2024 at 13:24 GMT-7

⟐ Answered Kasım 06, 2023 at 13:26 GMT-7

Cihaz 15-20 dk çalıştıktan sonra bu ekran kayması bitiyor sadece üst kısımda bi kaç çizgi şeklinde bir titretme kalıyor.

Bu sorun neden kaynaklanıyor ? Daha önce böyle bir sorun yaşayan olduysa yardımcı olabilirseniz sevinirim .


Hello, while my laptop was not having any problems, suddenly the screen started to slip.

After the device runs for 15-20 minutes, this screen shift ends, only a few lines remain at the top.

Why does this problem occur? If anyone has had this problem before, I'd appreciate it if you could help.

⟐ Edited by author Mart 25, 2021 at 16:09 GMT-7

⟐ Edited by author Aralık 26, 2020 at 5:04 GMT-7

Merhabalar. Bugün çözüme baştan macOS Catalina yükleyerek ulaştım. Bilgisayar kapalıyken alt+cmd+r tuşlarına basıp bilgisayarı açtım ve Recovery moduna girdi. Diskleri sildim ve cihaz internet üzerinden Catalina yazılımını indirip kurdu. Bilgisayardaki yavaşlık, ısınma gibi problemlerin hepsi çözüldü.

⟐ Answer deleted Aralık 21, 2020 at 16:49 GMT-7

Bilgisayar özellikleri hakkında çok fazla bir bilgim yok ama bazı programları kullanıyorum ve bazılarını öğrenmenmeye çalışıyorum. Sürekli olarak After Effects ve Premiere Pro kullanacağım ve başlangıç seviyesi olarak Cinema 4D. Bu programları kullanmak ve sıkıntısız render almak için aşağıdaki özellikler yeterli mi?

Macbook Pro 13”

• 1.4 GHz 4 çekirdekli 8. nesil Intel Core i5 işlemci, 3.9 GHz’e kadar Turbo Boost
• 16 GB 2133 MHz LPDDR3 bellek
• 256 GB SSD depolama
• True Tone özelliğine sahip Retina ekran
• Intel Iris Plus Graphics 645
• İki adet Thunderbolt 3 bağlantı noktası
• Touch Bar ve Touch ID

⟐ Commented Temmuz 22, 2019 at 17:35 GMT-7

Teşekkürler.

⟐ Answer edited Mart 21, 2019 at 6:32 GMT-7

Bu ne demek???

Bu uyarıyı aldığımda herhangi bir USB takılı değil???

⟐ Answer deleted Eylül 19, 2018 at 13:55 GMT-7

⟐ Commented Nisan 17, 2026 at 17:20 GMT-7

⟐ Commented Nisan 17, 2026 at 16:02 GMT-7

⟐ Commented Nisan 17, 2026 at 7:49 GMT-7

I boot it up to what I believe was an SSD with Monterey on it and I get either a no entry sign OR I get this.....

This suggests to me that the keyboard or Track Pad or both isn't detected, Yet the power button is working to turn it on and off, but it won't do a PRAM reset..... So I swapped over a new cable and it is the same. All I can do is connect a USB mouse and I get language option OR start up disc.... I checked the start up disc and I get this!

(10.10.5 Yosemite is NOT even supported on a 2017 model as they were originally shipped with Sierra 10.12).

I swapped out the SSD to a KNOWN SSD with Big Sur (Supported) and it is the same, telling me the OS on the SSD is Yosemite!. I thne put another SSD with Monterey pre installed and left at set-up and guess what, it STILL is the same telling me it is Yosemite! I can only think to just put the board into another case with a new keyboard and see if then I can wipe it clean and then to install fresh starting from High Sierra to Catalina, to Monterey (Safest way to get the correct boot ROM firmware installed.... I have NEVER used Yosemite OS and I am absolutely 1000% certain this had either Big Sur or Monterey installed on it's SSD which had not been removed or replaced or anything. Very odd, never seen something like this before. The board is clean, no water damage or anything obvious. Can anyone tell me what and why etc is going on here?

I swapped over the KB case and got into recovery and tried to install Monterey but all I get is a no entry sign..... PRAM was reset. Then tried with Catalina, the progress bar completed and so far so good.....I got into disc utility, selected show all devices and the internal SSD (KNOWN to be good) is not shown. Apple disk image & OS base system only appears, together with the external installer drive. YAY. I put back the 'Yosemite' SSD and it is recognized.... Attempting to install Catalina.... It is seemingly much slower than normal. It gets to disc utility and the internal SSD is NOT detected, again just the base system. I am running diagnostics and the report says SMC error codes

PPF004 (Fan) PPF003 (Fan)

VFD004 & VFD 005 (There may be an issue with the display or graphics processor.)

NDC001 (There may be an issue with the camera.)

PPN001 (There may be an issue with the power-management system.)

VDH002 (There may be an issue with a storage device.).

Everything is connected up fine. I then run the Paul Daniels SMC Tools and successfully updated the SMC. Booted up again and it went back to this screen showing a mouse to connect!. Only option was to select start up disk (Listed were 4 compatible systems from my multi OS bootable drive, I selected Catalina, restarted and I get the screen your computer has a problem. Yes I know LOL

Firmware password protection is turned OFF. Help!

UPDATE: We have put a new SMC chip & programmed it with SMC tools. We have swapped the BIOS chip from a 2017 donor board (But we are looking for a BIOS file to program it fresh if need be).... We swap out SSD's with compatible OS (Monterey) but are always greeted with a flashing folder and a high spinning fan. @oldturkey03

⟐ Commented Nisan 17, 2026 at 3:43 GMT-7