iFixit - Active Questions With Device "Tool"

Power Drill: Matkap ucu gevşiyor yerinden çıkıyor

Mon, 30 Mar 2026 02:21:53 -0700

Sıkma yada sökme sırasında matkap ucu gevşiyo

⟐ Answered Mart 30, 2026 at 2:21 GMT-7

Drill: Pil değişimi nasıl yapılır ustam

Fri, 24 Oct 2025 00:57:16 -0700

Pil değişimi nasıl yapılır

⟐ Commented Ekim 24, 2025 at 0:57 GMT-7

Black Decker Chainsaw: karbüratör tamiri avans ayarları

Wed, 05 Mar 2025 09:29:18 -0700

avans ayarları nasıl yapılıyor

DeWalt DC970: Tetik çalısmiyor motoru sağlam bataryası sağlam

Wed, 10 Apr 2024 22:32:44 -0700

Tetik mekanizmasındı arıza var

⟐ Answered Nisan 10, 2024 at 22:32 GMT-7

Ridgid Reciprocating Saw R8641 CS142914D05 2015: What is the orbital action

Tue, 16 Jun 2026 16:02:22 -0700

What is the orbital action?

⟐ Answered Haziran 16, 2026 at 16:02 GMT-7

Graco Paint Sprayers 17K301 2017: How do you replace the pump hose inside the unit?

Tue, 16 Jun 2026 11:45:57 -0700

How to replace the pump hose inside the unit ?

⟐ Commented Haziran 16, 2026 at 11:45 GMT-7

Tool: LED Driver / Ballast for 8' LED Tube light

Mon, 15 Jun 2026 18:27:05 -0700

Hi

I am working on 8' LED tube light. It uses HOSSONI LED Driver (Ballast) SDC96CS200V48DL1A.
The light keeps flashing, so suspect defective LED Driver. I am looking for this driver.

Input: 120Vac
Output: 36-48Vdc, Actual No-load voltage: 55Vdc
3-wires connected to the LED lights
3 position switch to select the color.
Aux Output: 0-10Vdc (Not used)
0-10Vdc for Dimmer So, a non-dimmable LED Driver should work.

Kindly suggest a cross for above driver?

Pic attached.

Question: A 3 position switch is used to set the color. Does this switch actually changes output currents to 1150mA, 1500mA, or 2000mA?

Thanks

⟐ Commented Haziran 15, 2026 at 18:27 GMT-7

Craftsman Riding Mower: I need a actual picture of the installed drive belt

Mon, 15 Jun 2026 01:07:02 -0700

Hello--

The belt snapped the drive belt on my Craftsman Riding Mower 917.987140 46" automatic, Well, When i installed the new belt, It is still loose and i have done what it looks like in th eowners manual, If anyone can help it would be very helpful, If i can get a actual picture that would be even better. Thanks, Email icitrish@aol.com

⟐ Commented Haziran 15, 2026 at 1:07 GMT-7

Pressure Washer: Diy pressure washer to a misting pump?

Sun, 14 Jun 2026 15:14:37 -0700

Hi, how to make a pressure washer deliver water out without pulling the trigger gun?

Please help. Thanks

⟐ Commented Haziran 14, 2026 at 15:14 GMT-7

Black and Decker BDEDMT: Replacement for discontinued trigger switch 90584431 (BDCDMT120)

Sun, 14 Jun 2026 07:55:55 -0700

I am looking for a replacement trigger switch for my Black & Decker BDCDMT120 20V Matrix cordless drill. I have identified the part number as 90584431, but it appears to be discontinued or no longer available (NLA) through most major parts distributors.

Does anyone know of a compatible alternative trigger switch or a substitution part number that works for this specific model? Are there generic 20V variable speed switches that are known to fit the housing and handle the current?

I am comfortable with soldering if needed, but I want to make sure the replacement will physically fit and function correctly with the Matrix system. Any advice or sources would be greatly appreciated!

⟐ Answered Haziran 14, 2026 at 7:55 GMT-7

FixHub Portable Soldering Station: Fixhub USB-c cable replacement

Sun, 14 Jun 2026 07:52:18 -0700

Hello,

My usb-c cable from the fixhub soldering iron broke does anyone know where to source it?

Thanks

⟐ Commented Haziran 14, 2026 at 7:52 GMT-7

Circular Saw: See wonders when cutting

Sun, 14 Jun 2026 01:16:18 -0700

My Kobalt 6.5 I believe she’s isnkisaligned wonders sometime toward the end of cut I know. Blade is straight t

⟐ Commented Haziran 14, 2026 at 1:16 GMT-7

Black And Decker Cordless Drill LDX220 2015: Why is my drill just suddenly stops and when I turn it on a smoke cameo

Sat, 13 Jun 2026 19:15:07 -0700

My drill is b&d that you can change it into circular saw, impact, drill or anything. When try turning it on after re-applying the battery and pull the power a lil bit, there's a sound which indicates there's a power, but when I pull the power all the way it won't spin and suddenly a smoke came out on reverse button

⟐ Answered Haziran 13, 2026 at 19:15 GMT-7

Makita Hammer Drill XPH012 2016: nó ko hoạt động

Sat, 13 Jun 2026 19:06:28 -0700

cấm pin đầy đủ mà ko hoạt động

⟐ Answered Haziran 13, 2026 at 19:06 GMT-7

Ryobi Blower P21081 2017: Tool needed to remove fan blade?

Sat, 13 Jun 2026 00:17:48 -0700

What tool do i use/need to remove the fan blade so I can replace it

⟐ Answered Haziran 13, 2026 at 0:17 GMT-7

Campbell Hausfeld Air Compressor VT619600AJ 2014: How do I remove plastic belt housing?

Fri, 12 Jun 2026 10:44:45 -0700

How do I remove plastic belt housing?

FixHub Portable Soldering Station: Intermittent "Tool Error: Sensor Disconnect" (Error #5) during heating - FixHub SLD101

Thu, 11 Jun 2026 12:39:44 -0700

I'm experiencing an intermittent "Tool Error: Sensor Disconnect" (Error Code #5) on my FixHub Portable Soldering Station during the heating phase.

Symptoms:

- While heating, the error flashes for ~1 second, the temperature display drops a few degrees, then heating resumes. This cycles repeatedly.

- Using firmware 1.5.0 on both Hub and Iron.

- Tip is a 1.5 Bevel.

Troubleshooting already performed:

- Verified tip is fully seated (clicked in, aligned below the surface).

- Cleaned 3.5mm contacts and internal handle springs with IPA.

- Disassembled the iron handle; internal soldering points for the socket are secure and show no signs of failure.

- Measured tip resistance at ~3 ohms at room temperature.

- Tested both front USB-C ports with the original cable (same result).

- Tested with third-party 100W cables (MacBook/IKEA), which resulted in Error #11 (No Data), confirming the hub requires the specific data lines of the original cable.

The intermittent nature suggests a thermal expansion break inside the tip's sensor circuit. Are there any known issues with this behavior or specific tests I can run to verify if it's the tip vs. the iron handle's internal logic?

⟐ Commented Haziran 11, 2026 at 12:39 GMT-7

Makita Nailer AN923 2016: Nail gun pin stuck out

Thu, 11 Jun 2026 09:38:01 -0700

I got a nail gun with the pin stuck out and doesn’t move

Air Compressor: How to set a switch one a 5 horse air compressor with a magnet switch

Thu, 11 Jun 2026 08:07:40 -0700

How to set a magnet switch on a air compressor

FixHub Portable Power Station: Power station working but display is not turning on

Tue, 09 Jun 2026 07:31:17 -0700

I received my soldering kit with power station a couple of weeks ago and when I first charged the power station with the display working well enough. Today I wanted to start soldering, but the display won't turn on. I'm able to see the power station in the web console and updated it to the latest FW without issues. The battery is shown to be at 100%.

However the display is still not functioning. Any help/tips appreciated.

⟐ Commented Haziran 09, 2026 at 7:31 GMT-7