the screen is not broken at all

Should i have to replace my screen or is this because the components are not intact.

Can anyone please suggest the best way in which I can repair it.

Please help !

[http://|https://drive.google.com/file/d/0B8nrv2Q...]

[http://|https://drive.google.com/file/d/0B8nrv2Q...]

⟐ Answered Haziran 03, 2018 at 13:06 GMT-7

I haven't had the screen replaced. I simply had the battery replaced by a third party seller.

What could have possibly gone wrong ?

Any advise is appreciated.

⟐ Commented Nisan 23, 2018 at 5:38 GMT-7

⟐ Answer accepted Nisan 21, 2018 at 7:23 GMT-7

⟐ Commented Ekim 31, 2017 at 20:03 GMT-7

Mine doesn't click anymore and I have to use the Virtual Home Button, which is useful, but annoying too.

⟐ Answer accepted Temmuz 12, 2017 at 18:40 GMT-7

Sorry about that, tried to post from a mobile and was unable to add a photo here is the photo, thanks for the help.

⟐ Commented Nisan 12, 2017 at 11:57 GMT-7

For about a year or so, my iPad mini 2 LTE has these about 1 pixel tall black lines that span along the bottom of the screen. They have one pixel span in between each one and the collective height is about 1cm from the bottom of the screen, I'll to attatch a photo because I doubt anyone knows what I'm saying.

It obviously is something to do with the LCD but, I was wondering if I needed a screen replacement or maybe the connection is off a bit, I don't really know.

PHOTOS OF ISSUE

⟐ Answered Nisan 08, 2017 at 21:36 GMT-7

⟐ Commented Şubat 18, 2017 at 19:20 GMT-7

The steps that I've tried so far are:

• Tried another battery
• Factory reset
• Tried various chargers and cables, both original and knock-offs

Any ideas? I've tried Googling and can't find anyone with a similar issue.

⟐ Answered Ocak 02, 2017 at 13:49 GMT-7

why did it fail in the first place, when it was working before?

is there any solution to fix this digitizer other than replacement?
e.g. putting tape around the edge of the screen, tape where the connectors are to prevent a short.

I know there can be other issues that occur after replacing the digitizer

e.g. ghost touch input

Is there anything that can be done to prevent the ghost touch input issue after replacement of the digitizer?

Note that the slow or semi-random charging had been present prior to the battery update, and began when the iPad last upgraded to some version of ios 12. (approx. a year of bad charging behavior, where it would jump from 4% to 100 % in a very short time.)

Initially, after the battery upgrade, it appeared to be stone dead - screen NOT lighting up at all. Left it on a charger for a couple of days, still nothing.

Connected it to a Mac MINI, and when I pressed the button, the device came on! but it showed 1 or 2 % power. The Mac MINI said that the device was “drawing too much power”, and I should disconnect it. Put it back on a charger for several days. It climbed to a staggering 4% battery level. Everything appears to work, touch screen, buttons, etc. Except for the sad state of charging.

Any obvious culprits?

⟐ Edited by author Aralık 01, 2021 at 16:08 GMT-7

when it sleeps. you can’t wake it other than turning on the backlight. Able to sleep+home to restart ipad.

after pressing sleep or auto sleep, you can still hear siri and sleep/cover clicks.

I understand that the mini 4,5 have a sleep/wake switch. am i wrong in thinking the mini 2 does not?

- Power button does not lock the iPad however, shut down works (long press)

- Many Apps like MS Teams gets installed; however, cannot join any sessions

- Overall, the iPad is much slower than it used to be

Actions Taken

- Erased All contents and Settings to Factory Default many times upto iOS 12.5.4

I have an iPad mini 2 which randomly either takes screenshots when I press the home button or displays ‘slide to power off’ screen. I realise that these both point towards a stuck or intermittent power button but I have replaced this and also replaced the digitizer to rule that out. Unfortunately it’s still the same. Has anyone experienced this before?

Thanks in Advance

Change digitizer and lcd on ipad mini 2 all went fine worked perfectly, went to check it the next day and there was a random rainbow effect in the middle of the digitizer.

Anyone had this problem.

Thanks

Andy

⟐ Edited by author Eylül 03, 2019 at 22:12 GMT-7

It's missing a solder pad (No2) can anyone help on where or what

i need to run a cable to to gerrt it working ???

i have the same problem with an ipad pro 12.9. Anyone can help me to find that component? where i can buy a new one? i haven't a donor motherboard.

thanks

⟐ Edited Aralık 29, 2017 at 18:51 GMT-7