is it safe to continue taking it out, or will the phone catch on fire?

all done, had to pry, the pull tabs weren't strong and broke straight away. scary AF

⟐ Commented Mart 29, 2022 at 10:21 GMT-7

⟐ Commented Temmuz 26, 2021 at 8:19 GMT-7

Very very strange issue actually. I repair iPhones since years, nearly saw everything during that time but not that.

I got an iPhone 6 with a battery which was bloated a bit. It worked well so far, but pushed at the back-side of the LCD. So we needed to replace it.

I still had a replacement battery onsite (3rd party) and tried it: Battery charging stays at 1% for hours. Nothing is happening - the iPhones shows "charging" the whole time. Other cable, adapter: same problem. So I tested the original iPhone battery again which charges well.

So I ordered another battery from another vendor. It arrived yesterday. I installed it today in the morning, started the iPhone and plug in the charger. The battery had a charge of 42% at this time.

Now, after several hours, it still remains on 42%. The original old / blown battery charges well again.

So I am getting crazy now. Is it really possible that I got two 3rd battery batteries from the same vendor with the same issue? I can't believe that. But regarding to the fact the original battery do it fine I do not have any other ideas. Or did someone had the same problem in the past?

Many thanks!

⟐ Answered Mayıs 13, 2021 at 12:23 GMT-7

⟐ Comment deleted Ocak 29, 2021 at 23:41 GMT-7

This is what I have tried:

-resetting router

-Factory reset on phone

-Reset Network settings on phone

-Disabling bluetooth on phone

-Disabling "wifi networking" under phone settings-->privacy-->location services-->wifi networking

-Switching dns to ( 8.8.8.8 ) , ( 8.8.4.4) , and ( 8.8.8.8,8.8.4.4 )

-Renewing Lease  through phone 

-Switching Channels through router settings

⟐ Commented Aralık 27, 2020 at 2:06 GMT-7

https://youtu.be/m8bLkwm9hJc

And I also want to say at first, that I already changed the Display and the battery but the following problem still exist:

I have a problem with an IPhone 6. There is a 50/50 chance the display starts flickering or not when turning on the display. I think it's the backlight. If it doesn't start to flicker after turning on the display it's all okay...but if it starts flickering after turning on the display, it will not stop until turning off the display.

So it just starts in the moment when the display flashes on and never comes when the display is already on without flickering.

So does anybody has an idea, what's the problem here? What part can I check or which IC /Filter / ..... do I have to change?

I hope someone can help me.

Thanks :)

⟐ Answered Temmuz 01, 2020 at 12:27 GMT-7

⟐ Commented Nisan 30, 2020 at 5:02 GMT-7

When i try to restore i always get itunes error 9. Before it worked great.

I didn't drop it nothing, i just wanted to do an update and this happens.

i tried i4tools but it stays at 20 % "Nor Data".

One time it went to 80 per cent but then crashed.

i spent more than 4 hours on it but didn't find any solution.

Any help would be greatly appreciated.

⟐ Commented Ağustos 11, 2019 at 13:26 GMT-7

Thanks very much in advance.

⟐ Commented Mart 13, 2019 at 4:44 GMT-7

if it's possible then what pins do i connect the wires to and what volt/amps to set?

and also is it possible to connect the iPhone to the dc power supply directly? and if so what pins do i connect the wires to and what volt/amps to set?

thanks

⟐ Answered Şubat 14, 2019 at 2:40 GMT-7

⟐ Answer accepted Eylül 15, 2018 at 10:32 GMT-7

⟐ Commented Nisan 15, 2018 at 20:47 GMT-7

Thanks

⟐ Commented Eylül 23, 2016 at 7:33 GMT-7

Thank you.

⟐ Answered Ocak 15, 2016 at 2:22 GMT-7

I know every component on iphones but I'm not even sure where to start with the temperature, is that something within the IOS? or a part on the phone itself that could be damaged?

Thanks.

⟐ Answered Haziran 11, 2025 at 20:26 GMT-7

⟐ Answered Nisan 23, 2025 at 4:10 GMT-7

And, iPhone battery 6 Plus is compatible with the iPhone 6S Plus?

I tried to place the battery iphone 6 Plus, in the iPhone 6S Plus, and the phone worked, but not sure is there any problem in using this battery.

⟐ Answered Ağustos 25, 2023 at 23:44 GMT-7

I've been giving glass-only repairs a try recently, and the only issue I came in contact with was where LOCA glue would enter the backlight of the LCD. I've seen many videos and guides already, and some suggest just using a mold, others say blue tac works well, but there doesn't seem to be a good solution to this yet.

Therefore I wanted to ask if anyone has more experience in this and if anyone has any suggestions.

Yes, I know that OCA exists, but I want to keep the repairs affordable. I have seen an item on eBay which is a LCD backlight sealant (some sort of glue which is put onto the sides of the LCD (http://www.ebay.de/itm/371221025033)) but I have not seen any reviews about it yet. I also tried using electircal tape, but liquids get underneath anyway. Maybe thin double sided sticky tape works? I have also heard people removing the backlight first, but how do you reattach it?

Also little sidenote: Does a LOCA glass replacement work on iPhone 6s too? It should, but since the 6s has 3D touch, this may be a problem.

I would be happy to hear from you guys!

⟐ Commented Ocak 03, 2023 at 21:55 GMT-7

What could be the problem? Have tried multiple LCD's but still having same problem.

⟐ Commented Şubat 18, 2022 at 22:47 GMT-7

As I cannot replace the Home Button, my only option is to attempt to remove the connector. I have tried using tweezers but the package is too small. My next idea was to slightly heat the tip of my soldering iron and see if the connector will grip onto the tip of the iron. However if I break this button My iPhone is bricked and done so I wanted to see if you guys had any tips for me!

Sorry for the poor image quality but I don't have a camera available that can zoom in far enough.

Thanks!

⟐ Answered Nisan 08, 2021 at 17:57 GMT-7