⟐ Answer accepted Ocak 13, 2019 at 8:17 GMT-7

⟐ Commented Ocak 10, 2019 at 21:40 GMT-7

⟐ Commented Ocak 05, 2019 at 6:38 GMT-7

⟐ Answered Ocak 03, 2019 at 18:03 GMT-7

⟐ Answered Aralık 26, 2018 at 17:45 GMT-7

Thanks,

Rob

⟐ Commented Aralık 21, 2018 at 15:21 GMT-7

⟐ Answered Aralık 06, 2018 at 5:32 GMT-7

⟐ Commented Aralık 05, 2018 at 22:06 GMT-7

I put the power supply on the battery connector and it is constantly taking 0.03A(motherboard tooked out of the case) and when i press the power button it takes 0.11A and it is not coming on.

Where should i check first? I have everything i need (power supply, hot air gun, soldering iron,etc.)

Thanks, i need your ideas!

⟐ Commented Aralık 01, 2018 at 3:37 GMT-7

After replacing the screen and hooking everything back up to the logic board I got a black screen. I absolutely made sure to disconnect the battery before ever touching any other part of the phone. I have also tried connecting it to iTunes and got as far as it asking for the passcode which I cannot enter as the screen does not work.

Now here's where it gets hairy and I'm stuck, after looking through the various other similar questions I attempted to test if thew screen was bad by replacing the severely cracked screen, which I knew worked. After taking all the assembly parts off the new screen and putting them back on and trying to plug it in, I got nothing.

It's still being recognized by iTunes, but now no matter which screen I have plugged in I get a black screen. I have a sinking feeling it's going to require board level repair (which I can't do, yet) but I'm hoping maybe someone here can see something I can't.

If there's something you think may help me get this problem remedied or you need more information on what all I did to it, just ask and I'll happily provide more info. Thanks everyone.

⟐ Commented Kasım 25, 2018 at 12:07 GMT-7

My client told me the, he close his car door and the phone remain inside.

Mother Board appereantly perfect.

I check with multimeter, and find VCC main short.

I check with power supply, the phone absorb current without power on.

I check it with cold spyay, the first part hot is : Q2300.

I put it out and check, but shortage remain.

Now when i connect the phone with DCPS, not happen nothing (no hot but not turn on)

I try to connect the vcc line with dc power supply and give the current in this line, but phone not hot.

My question is :

Somebody plz telle me if i connect the wire correctly ?

Is there any problem if i use for do this the jumper wire (very fine wire)?

How much current i give the phone, for verify it?

The strange thing is , i set set the voltage on DCPS, (2.5V) (PIC 1)

but when i solder the cable on vcc line, the voltage value automatic change. (PIC 2)

Which is the Maximun current i give the phone for verify short?

My last question is : In the PIC 1, when i connect the cable Only with DCPS (and not to any phone) the current line automatic change , its mean there is something defect on the cable?

thanks a lot in Advanced for patience and attention :)

Update

⟐ Answer accepted Kasım 23, 2018 at 10:21 GMT-7

I have an iPhone 6s. A week or so ago, the screen was completely shattered and the screen began to press into the touch screen below it; the phone then began to type in random passwords all the time. After a night or so, the phone said “iPhone is disabled. Connect to iTunes.” I couldn’t do anything about it because of the screen. Today, I got my screen fixed and the phone still said Connect to iTunes. I plugged it into my HP laptop computer with multiple chords but it didn’t connect. I’m not sure which device is the issue. The computer will accept any other USB, and the iPhone is accepting any other computer. So the issue is, I cannot connect to iTunes to restore my phone. I cannot use the iTunes website to start up my phone because I need a confirmation code… which would be sent to my phone, so I couldn’t see it. I have not logged into any other device with my iTunes. I had it factory reset but it still says connect to iTunes. What can I do???

(sorry about how confusing it is.)

⟐ Answered Kasım 22, 2018 at 2:42 GMT-7

⟐ Answer accepted Kasım 21, 2018 at 6:08 GMT-7

⟐ Answer accepted Kasım 18, 2018 at 7:59 GMT-7

⟐ Answered Kasım 16, 2018 at 3:40 GMT-7

⟐ Answered Kasım 15, 2018 at 10:22 GMT-7

⟐ Commented Kasım 10, 2018 at 21:31 GMT-7

⟐ Answered Kasım 08, 2018 at 21:03 GMT-7

Yesterday I dropped my iPhone 6s. And when I picked it up nothing happened - at least what I could see. When I came home I realized that both cameras and my flashlight weren't working.

The phone has not been in contact with water.

The earpiece speaker is working.

Any ideas what I could do to fix it?

⟐ Answer accepted Kasım 07, 2018 at 12:04 GMT-7

• Battery Changed to new oem battery about 1 month ago.
• Phone wont stay on, reboots like 1-10 minutes from starting to use it.
• Constant reboots connected to PC, fine on Charger.
• Charges from 1% to 100% (i would say fake charge) in 10 - 30 seconds and shuts down immidiately when taken from charger, unless the phone has been in the charge for time where normal working iphone charges 20%.
  
• Phone has only been used on PC or original Apple charger that came in the box.
  

Tristar, Battery or Lightning Port issue?

New OEM battery broke after just week in the phone. Wonder if its the phone or replacement battery causing the issue?

⟐ Edited by author Kasım 01, 2018 at 20:27 GMT-7