Ana içeriğe geç
Yardım

Güncel sürümün sahibi: oldturkey03 ,

Metin:

Grady, to get to your lens assembly as well as the ribbon cable with the CMOS sensor attchedattached to the back of the lens, follow [guide|32716|this guide] first. Then proceed with the main frame removal. Lay the camera on the front and remove the two screws holding the main frame to the plastic battery housing Red Arrows.
Grady, to get to your lens assembly as well as the ribbon cable with the CMOS sensor attchedattached to the back of the lens, follow [guide|32716|this guide] first. Then proceed with the main frame removal. Lay the camera on the front and remove the two screws holding the main frame to the plastic battery housing Red Arrows.
[image|465775|align=center]

There
There are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the way. These instructions are from An Illustrated Guide to Help You Repair Your PowerShot® A4000 James W. Pasek.

There
There are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the way. These instructions are from An Illustrated Guide to Help You Repair Your PowerShot® A4000 James W. Pasek.
Pry the ribbon cable retainer clamps up from the lens controller cable
 
[image|465776|align=center]

Red
Red Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video. These instructions are from An Illustrated Guide to Help You Repair Your PowerShot® A4000 James W. Pasek.

Red
Red Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video. These instructions are from An Illustrated Guide to Help You Repair Your PowerShot® A4000 James W. Pasek.

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

Grady, to get to your lens assembly as well as the ribbon cable with the CMOS sensor attched to the back of the lens, follow [guide|32716|this guide] first. Then proceed with the main frame removal. Lay the camera on the front and remove the two screws holding the main frame to the plastic battery housing Red Arrows.
[image|465775|align=center]
There

[image|465775|align=center]

There
are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the wayway. These instructions are from An Illustrated Guide to Help You Repair Your PowerShot® A4000 James W. Pasek.
[image|465775|align=center]
There

[image|465775|align=center]

There
are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the wayway. These instructions are from An Illustrated Guide to Help You Repair Your PowerShot® A4000 James W. Pasek.
 
Pry the ribbon cable retainer clamps up from the lens controller cable
[image|465776|align=center]Red
[image|465776|align=center]

Red
Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video.
[image|465776|align=center]Red
[image|465776|align=center]

Red
Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video.

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

Grady, to get to your lens assembly as well as the ribbon cable with the CMOS sensor attched to the back of the lens, follow [guide|32716|this guide] first. Then proceed with the main frame removal.

Lay
Lay the camera on itsthe front face and remove the two screws holding the main frame to the plastic battery housing

[image|465775|align=left]

Red
Red Arrows. There
[image|465775|align=center]
There
are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the way
Grady, to get to your lens assembly as well as the ribbon cable with the CMOS sensor attched to the back of the lens, follow [guide|32716|this guide] first. Then proceed with the main frame removal.

Lay
Lay the camera on itsthe front face and remove the two screws holding the main frame to the plastic battery housing

[image|465775|align=left]

Red
Red Arrows. There
[image|465775|align=center]
There
are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the way
 
Pry the ribbon cable retainer clamps up from the lens controller cable

[image|465776|align=left]

Red
[image|465776|align=center]Red Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video.

[image|465776|align=left]

Red
[image|465776|align=center]Red Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video.

Durum:

open

Orijinal gönderinin sahibi: oldturkey03 ,

Metin:

Grady, to get to your lens assembly as well as the ribbon cable with the CMOS sensor attched to the back of the lens, follow [guide|32716|this guide] first. Then proceed with the main frame removal.

Lay the camera on its front face and remove the two screws holding the main frame to the plastic battery housing

[image|465775|align=left]

Red Arrows. There are two small Phillips screws holding the lens assembly to the metal camera frame (Blue Arrows.) These are tightly threaded into the plastic lens housing back plate. Make sure that you use a #0 Phillips screwdriver and constant pressure while you are unscrewing them to prevent stripping out the head. The screw holding the flash unit (Green Arrow) can be removed if you are replacing the unit, otherwise the flash unit can remain attached to the main frame and removed along with the frame. Slide the main frame to the left to get the drive motor out from under the flash unit and then lift it out of the way

Pry the ribbon cable retainer clamps up from the lens controller cable

[image|465776|align=left]

Red Arrow and the CCD controller cable Blue Arrow. Slide out the cables to remove the lens assembly. You can now proceed to loosen the ribbon cables from the back of the lens and take a look at the sensor. For a complete work on your lens, take a look [https://www.youtube.com/watch?v=PcO7WoRPRbM|at this] video.

Durum:

open