Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Yardım

Güncel sürümün sahibi: Jimfixer ,

Başlık:

Looking for a little help

Metin:

Im rebuilding the wire speed control on my small welder and am wondering if anyone knows where i can find a three terminal rotary rheostat 115 volt 250vac 40 amp . The company I bought the welder from is in Italy and no longer has any dealers in my area and when i contacted the company they said they wont sell parts to end users . The web site they sent is all in Italian  . Got a friend to translate for me and even hes not sure how to get what I need . I've gone over the cuircit board and am pretty certain the problem is in the rheostat. @oldturkey03  Mike im kinda directing this in your direction but will take help from anyone Im just not finding anything

'''Update'''

The welder is a Deca 150e Its a portable welder I use at job sites without 220 outlets as this runs off 110

[image|1294361]

[image|1294362]

[image|1294366]

I have my thumb on the rheostat it measures 1 1/4"by 3/4wide

size doesnt really mater as I can adapt to most any size .

Just to let you know what I've tried . I replaced the entire board with a model train controller that worked great on low settings but burned out on the high setting . I've also tried a dimmer switch with similar results

Cihaz:

Welder

Durum:

open

Kabul Edilen Cevap:

446363

Düzenleyen: Aiden Baker ,

Başlık:

Looking for a little help

Metin:

Im rebuilding the wire speed control on my small welder and am wondering if anyone knows where i can find a three terminal rotary rheostat 115 volt 250vac 40 amp . The company I bought the welder from is in Italy and no longer has any dealers in my area and when i contacted the company they said they wont sell parts to end users . The web site they sent is all in Italian . Got a friend to translate for me and even hes not sure how to get what I need . I've gone over the cuircit board and am pretty certain the problem is in the rheostat. @oldturkey03 Mike im kinda directing this in your direction but will take help from anyone Im just not finding anything
Im rebuilding the wire speed control on my small welder and am wondering if anyone knows where i can find a three terminal rotary rheostat 115 volt 250vac 40 amp . The company I bought the welder from is in Italy and no longer has any dealers in my area and when i contacted the company they said they wont sell parts to end users . The web site they sent is all in Italian . Got a friend to translate for me and even hes not sure how to get what I need . I've gone over the cuircit board and am pretty certain the problem is in the rheostat. @oldturkey03 Mike im kinda directing this in your direction but will take help from anyone Im just not finding anything
'''Update'''
 
The welder is a Deca 150e Its a portable welder I use at job sites without 220 outlets as this runs off 110
 
[image|1294361]
 
[image|1294362]
 
[image|1294366]
 
I have my thumb on the rheostat it measures 1 1/4"by 3/4wide
size
size
doesnt really mater as I can adapt to most any size .
size
size
doesnt really mater as I can adapt to most any size .
Just to let you know what I've tried . I replaced the entire board with a model train controller that worked great on low settings but burned out on the high setting . I've also tried a dimmer switch with similar results

Cihaz:

WireWelder
WireWelder

Durum:

open

Düzenleyen: Jimfixer ,

Başlık:

Looking for a little help

Metin:

Im rebuilding the wire speed control on my small welder and am wondering if anyone knows where i can find a three terminal rotary rheostat 115 volt 250vac 40 amp . The company I bought the welder from is in Italy and no longer has any dealers in my area and when i contacted the company they said they wont sell parts to end users . The web site they sent is all in Italian . Got a friend to translate for me and even hes not sure how to get what I need . I've gone over the cuircit board and am pretty certain the problem is in the rheostat. @oldturkey03 Mike im kinda directing this in your direction but will take help from anyone Im just not finding anything
'''Update'''
The welder is a Deca 150e Its a portable welder I use at job sites without 220 outlets as this runs off 110
[image|1294361]
[image|1294362]
[image|1294366]
I have my thumb on the rheostat it measures 1 1/4"by 3/4wide
size doesnt really mater as I can adapt to most any size .
Just to let you know what I've tried . I replaced the entire board with a model train controller that worked great on low settings but burned out on the high setting . I've also tried a dimmer switch with similar results
Im rebuilding the wire speed control on my small welder and am wondering if anyone knows where i can find a three terminal rotary rheostat 115 volt 250vac 40 amp . The company I bought the welder from is in Italy and no longer has any dealers in my area and when i contacted the company they said they wont sell parts to end users . The web site they sent is all in Italian . Got a friend to translate for me and even hes not sure how to get what I need . I've gone over the cuircit board and am pretty certain the problem is in the rheostat. @oldturkey03 Mike im kinda directing this in your direction but will take help from anyone Im just not finding anything
'''Update'''
The welder is a Deca 150e Its a portable welder I use at job sites without 220 outlets as this runs off 110
[image|1294361]
[image|1294362]
[image|1294366]
I have my thumb on the rheostat it measures 1 1/4"by 3/4wide
size doesnt really mater as I can adapt to most any size .
Just to let you know what I've tried . I replaced the entire board with a model train controller that worked great on low settings but burned out on the high setting . I've also tried a dimmer switch with similar results

Cihaz:

Wire

Durum:

open

Orijinal gönderinin sahibi: Jimfixer ,

Başlık:

Looking for a little help

Metin:

Im rebuilding the wire speed control on my small welder and am wondering if anyone knows where i can find a three terminal rotary rheostat 115 volt 250vac 40 amp . The company I bought the welder from is in Italy and no longer has any dealers in my area and when i contacted the company they said they wont sell parts to end users . The web site they sent is all in Italian  . Got a friend to translate for me and even hes not sure how to get what I need . I've gone over the cuircit board and am pretty certain the problem is in the rheostat. @oldturkey03  Mike im kinda directing this in your direction but will take help from anyone Im just not finding anything

Cihaz:

Wire

Durum:

open