Ana içeriğe geç
Yardım

Güncel sürümün sahibi: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. Yours looks like it is at 12V try to switch it to 5V. Keep your fingers crossed and see what you get.
 
== UPDATE 08/12/2018 ==
Looks like the T-con board runs kind of hot. Check the fuse to make sure you got continuity as well as power when your TV is on. Check to make sure it is just the thermal pad that is crooked and that there are not issues with the processor
 
[image|1521542]
 
According to your T-con board your display panel is a T315XWO2 VL Here is the datasheet for that. You may need it later on [document|4879]
 
Interestingly enough the T-Con board as well as the Inverter V266-001 are identical to a Sony KDL-32L4000 I am now wonderinggoing to check if this is a rebranded Sony……the Sony manual will give us more information.
Interestingly enough the T-Con board as well as the Inverter V266-001 are identical to a Sony KDL-32L4000 I am now wonderinggoing to check if this is a rebranded Sony……the Sony manual will give us more information.

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. Yours looks like it is at 12V try to switch it to 5V. Keep your fingers crossed and see what you get.
 
== UPDATE 08/12/2018 ==
Looks like the T-con board runs kind of hot. Check the fuse to make sure you got continuity as well as power when your TV is on. Check to make sure it is just the thermal pad that is crooked and that there are not issues with the processor
 
[image|1521542]
 
According to your T-con board your dispalydisplay panel is a T315XWO2 VL Here is the datasheet for that. You may need it later on [document|4879]

Interestingly enough the T-Con board as well as the Inverter V266-001 are identical to a Sony KDL-32L4000 I am now wondering if this is a rebranded Sony……
According to your T-con board your dispalydisplay panel is a T315XWO2 VL Here is the datasheet for that. You may need it later on [document|4879]

Interestingly enough the T-Con board as well as the Inverter V266-001 are identical to a Sony KDL-32L4000 I am now wondering if this is a rebranded Sony……

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. Yours looks like it is at 12V try to switch it to 5V. Keep your fingers crossed and see what you get.
 
== UPDATE 08/12/2018 ==
Looks like the T-con board runs kind of hot. Check the fuse to make sure you got continuity as well as power when your TV is on. Check to make sure it is just the thermal pad that is crooked and that there are not issues with the processor
 
[image|1521542]
 
According to your T-con board your dispaly panel is a T315XWO2 VL Here is the datasheet for that. You may need it later on [document|4879]

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. Yours looks like it is at 12V try to switch it to 5V. Keep your fingers crossed and see what you get.
 
== UPDATE 08/12/2018 ==
Looks like the T-con board runs kind of hot. Check the fuse to make sure you got continuity as well as power when your TV is on. Check to make sure it is just the thermal pad that is crooked and that there are not issues with the processor
 
[image|1521542]

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. IfYours looks like it is a 5Vat 12V try to switch it to 12V and vice versa5V. Keep your fingers crossed and see what you get.
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. IfYours looks like it is a 5Vat 12V try to switch it to 12V and vice versa5V. Keep your fingers crossed and see what you get.

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 


j@jafinch78
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. If it is a 5V try to switch to 12V and vice versa. Keep your fingers crossed and see what you get.


j@jafinch78
@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. If it is a 5V try to switch to 12V and vice versa. Keep your fingers crossed and see what you get.

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
No schematic seems to be available for your main board B.ZRAT3C-5
 
 
 
j@jafinch78 check the jumper '''CN4''' on B.ZRAT3C-5 8374 and see if it is on 5V or 12V. Any chance this could have been switched. If it is a 5V try to switch to 12V and vice versa. Keep your fingers crossed and see what you get.

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc.
 
[image|1521200]
 
== UPDATE 08/11/2018 ==
here is the
No schematic seems to be available for your power supply. Different revision but it will still give you the same ouputs etc. [image|1521200]main board B.ZRAT3C-5
== UPDATE 08/11/2018 ==
here is the
No schematic seems to be available for your power supply. Different revision but it will still give you the same ouputs etc. [image|1521200]main board B.ZRAT3C-5

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as the voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
 
 
 
== UPDATE 08/11/2018 ==
here is the schematic for your power supply. Different revision but it will still give you the same ouputs etc. [image|1521200]

Durum:

open

Düzenleyen: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as teh voltasgesthe voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.
@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your LED power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as teh voltasgesthe voltages that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.

Durum:

open

Orijinal gönderinin sahibi: oldturkey03 ,

Metin:

@jafinch78 this “did notice what looked like discoloration  “ could be an issue with your power board. You want to go ahead and post some good pictures of all of your boards with your question. Use this guide [guide|21499] for that. It will allow us to see what you see. You will have to have a multimeter to see if your power board as teh voltasges that are required to run your TV. There is not to much information about your Proscan so we will have to rely on your troubleshooting skills.

Durum:

open