Ana içeriğe geç

A baby monitor made by Infant Optics, Inc. The DXR-8 features a 3.5" screen , temperature sensor, night vision, and an interchangeable lens system.

33 Soru Tümünü görüntüle

DXR-8 camera fell - how do I pull it apart?

I hear a little rattle or something loose inside of it. I just need to open it to take a look inside!

Update (11/04/2018)

Block Image

@jayeff please see attached picture. I meant the whole thing came out not just the external add on.

Thanks!

Bu soruyu yanıtla Ben de bu sorunu yaşıyorum

Bu iyi bir soru mu?

Puan 0
4 Yorum

Lorena Heemsen is that rattling on the camera or the monitor?

tarafından

It's inside the camera. I was able to slightly open up the round part of the camera but I can't pull apart the sides so that I may pull it all apart and really get in there!

tarafından

Hello friends. The lens inside the camera got dismounted after falling on the ground. How to open the camera to put it back in place? Thanks

tarafından

@h_mhanna Have you checked the link posted by @jayeff to see if it will help?

tarafından

Yorum Ekle

4 Cevap

Filtre ölçütü:
En Yararlı Yanıt

Hi @ Deren Akinci,

Here’s the ifixit Infant Optics DXR-8 Camera Motherboard Replacement guide.

See the image in Step.12 as it shows where the ribbon cable connects to on the motherboard. Note the procedure written next to the image that describes how to unlock the connector to remove the cable. Make sure it is unlocked before trying to insert the cable and then lock it to hold the cable in.

Bu yanıt yardımcı oldu mu?

Puan 1
Yorum Ekle

Hi @h_mhanna ,

Here’s a link to the ifixit Infant Optics DXR-8 Lens Replacement guide which may be of some help in refitting the lens

Bu yanıt yardımcı oldu mu?

Puan 0

1 Yorum:

Hi @h_mhanna ,

Check on the base of the camera unit if you can tell whether the "feet" have covers that can be prised out that are hiding any screws. If they are just molded plastic then the whole case may be a of a snap fit construction

tarafından

Yorum Ekle

Thanks again @jayeff!

yes it looks like the attached picture. I’ll try to take the “feet” covers off.

Block Image

Bu yanıt yardımcı oldu mu?

Puan 0

6 Yorum:

Hi @h_mhanna ,

Try the pointed end of a Stanley knife - knife with a razor blade as the adjustable cutting edge or a safety razor blade from a scraper to get in and prise them out

Worst case scenario if they wont prise out easily is to push through the centre with a small screwdriver and lift them out this way. This will destroy them but it appears as though the unit doesn't rest on them anyway as they seem to be below the level of the base.

tarafından

Yes I’ll try to do that when I get a chance and will let you how it goes. Thanks a lot @jayeff

tarafından

It happend the same to mine. Did you find a way to open it up?

tarafından

I ended up sending it back. Infant optics is replacing it for us.

tarafından

But yes once you remove the feet covers you can access the screw and open the camera. Fairly straightforward. Thanks a lot @jayeff

tarafından

1 tane daha yorum göster

Yorum Ekle

Block Image

Block Image

my camera lens fell right out. Would anyone know where I attach those connections on the chip board?

Bu yanıt yardımcı oldu mu?

Puan 0

1 Yorum:

how to reconnect the camera

tarafından

Yorum Ekle

Yanıtını ekle

Lorena Heemsen sonsuza kadar minnettar olacak.
İstatistikleri Görüntüle:

Son 24 Saat: 3

Son 7 gün: 18

Son 30 gün: 65

Her zaman: 4,835