Eşyalarını Tamir Et Topluluk Mağaza

Repair information and guides for the iPhone 6 that was released on September 19, 2014. Model Numbers: A1549, A1586, and A1589

4994 Soru Tümünü görüntüle

Seçenekler

Water damaged iPhone with no visual damage or corrosion

Block Image

When i was taking off the shields i floated this chip and i lost it, can someone tell me the type of the chip, so i can get a new one.

I tested the screen and it works, all the connectors on the board are looking good, no corrosion or oxidation, i cleaned the board with alcohol , removed all the shields and visually inspected it, but still it does’t turn on. At the moment i do not have ultrasonic cleaner.

Yanıtlandı! Cevabı görüntüle Ben de bu sorunu yaşıyorum

Bu iyi bir soru mu?

Evet Hayır
Puan 0
Yorum Ekle

3 Cevap

Filtre ölçütü:
En Faydalı En Yeni En eski
Seçilen Çözüm

Seçenekler

The missing IC is U_LB_SW and it is part of the Low Band circuitry. IMHO, this is not a required IC and should not impede the phone from booting. If you want to replace it, you can either scavenge it from a donor board or order one on Aliexpress.

Daniel makes a good suggestion and if that isn’t the issue, the you need to start probing the circuitry to see if there any shorts. Start with VCC_MAIN, BATT_VCC and then move onto the PMIC outputs.

Bu yanıt yardımcı oldu mu?

Evet Hayır
Puan 2

4 Yorum:

So in theory this missing IC wont't interrupt the work of the phone?

tarafından

And yes i don't see any damage from water around the capacitor, but it should be somewhere on the edges because the water probably soaked from there.

tarafından

I've never tried a board with that IC removed so I can't say for certain. However, it doesn't look (according to the schematic) like it would be critical. Worse case, replace it first and then troubleshoot.

tarafından

Maybe the alcohol cleaning took effect but not on the same day, because today the phone booted up without a problem, so you were right about that ic.

tarafından

Yorum Ekle
En Yararlı Yanıt

Seçenekler

did you check the capacitor beside the wifi chip before removing the shields as its the most common issue

Bu yanıt yardımcı oldu mu?

Evet Hayır
Puan 2

3 Yorum:

No i didn't probe the capacitor before removing all the shields, i did now, and it looks fine, i tested around with continuity mode and it's not shorted nor any visual damage from water. Like Minho said now i will test VCC and then continue probing other lines to spot the shorted i guess.

tarafından

that cap is vcc_main so it would have told you if vcc_main was shorted before removing the shields. check the battery connector to check for a vbat short

tarafından

I was getting to think that it was a vbat short because there was no power, but then the screen turned on with some stripes on it.. So then i realize that the connector was little bended and loose. Тhe cleaning took effect!

And is it normal the CPU to get very hot when booting?

tarafından

Yorum Ekle

Seçenekler

The home button’s flex cable caused the problem, because i tried connecting only the LCD and it works fine, but when i connect the home button to the board, the phone immediately goes off, or when i connect the cable while the phone is off it doesn’t turn on. Now i saw oxidation where the home button connects to the flex cable on the back side of the screen.

Bu yanıt yardımcı oldu mu?

Evet Hayır
Puan 0

2 Yorum:

its possible i have had phones with bad home buttons before that caused the phone not to boot. as for the cpu getting hot it could be anything

tarafından

Yup it's the home button!

But for the cpu, it gets hot only when booting, after that it's absolutely fine.

tarafından

Yorum Ekle

Yanıtını ekle

Angewolf sonsuza kadar minnettar olacak.
İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 170