Ana içeriğe geç

Model A1181: 1.83, 2, 2.1, 2.13, 2.16, 2.2, or 2.4 GHz Core 2 Duo processor

1203 Soru Tümünü görüntüle

How to get MacBook to boot with no keyboard?

Hi, how do I boot a 2006 macbook (power button on logic board is a black chip) without the keyboard? I think the keyboard connector on the board is bad, but I dont know which to short on that chip to boot the computer with no keyboard! Thanks

Steve

Yanıtlandı! Cevabı görüntüle Ben de bu sorunu yaşıyorum

Bu iyi bir soru mu?

Puan 1
Yorum Ekle

5 Cevap

Filtre ölçütü:
Seçilen Çözüm

Unfortunately these models don't have the jump pads that the MacBook Pro range has to start the computer without the topcase. You will have to try another TC.

Bu yanıt yardımcı oldu mu?

Puan 1

5 Yorum:

ive tried several, the issue i think is in the connector on the actual logic board itself, not the top case.

tarafından

Well, could be a fried board then :-(

tarafından

found the issue, it wont run on magsafe, it will only run onbattery. now to diagnose!

tarafından

You got a lot of points here for a wrong answer. All A1181 MacBooks do have jump pads. Some are clearly marked by the power icon others are not so clearly marked by PWR BTN. On the ones with the icon the pads are right below the icon. On the boards you find PWR BTN the pads are about 1/2 inch to the left of the "words". In both cases the pads are located close to the cooling fan.

tarafından

ABCellars is 100% correct, the original answer is WRONG! You can start the computer by touching those two contact pads together. On my 13" Core 2 Duo 2.0Ghz the contacts were below the fan, 1/2" to the left of the silk screen PWR BTN

tarafından

Yorum Ekle
En Yararlı Yanıt

Görsel içeriğini görün:

Block Image

Bu yanıt yardımcı oldu mu?

Puan 7

1 Yorum:

Touch those two contacts together and the machine will boot up just like pressing the keyboard power button. Works the same way for a hard reset, just touch those two contacts together for 3+ seconds.

tarafından

Yorum Ekle

yes you can see the pic

https://picasaweb.google.com/simran.sing...

Bu yanıt yardımcı oldu mu?

Puan 5

4 Yorum:

+ excellent find

tarafından

first link was empty now i have changed that

tarafından

this computer does not have that, i can do that on another mac i have on hand, but this one was a chip with 3 solder points labeled PWR BTN. i dont know if i can short any of those to make it start? i got the sleep status light to flash a single time once with no ram (so it just blinked) but nothing since..

tarafından

Look about a 1/2 inch to the left of the "words" PWR BTN you will see 2 pads with a line between them. Those are your jumper pads.

tarafından

Yorum Ekle

WELL I AM SO IMPRESSED WITH THIS THREAD THAT I TOOK A PHOTO OF MY LATE 2006 DUO CORE 2 MACBOOK, ITS AS PER ADVISE ABOVE. JUMP STARTING IS A CONFUSING WAY OF SAYING SHORT THE 2 PADS TOGETHER, AS SHOWN IN THE PHOTO. TOP CIRCUITS WITH THE KEYPAD AND TRACK PAD ARE COMMONLY AVAILABLE AT LOW COST AT THIS STAGE!

Block Image

- THIS WORKED FOR ME, NEW KEYPAD ORDERED!

FOR SOME REASON IFIXIT HAS ROTATED THE PHOTO!

Bu yanıt yardımcı oldu mu?

Puan 3
Yorum Ekle

I broke my working keypad's ribbon as I unmounted it several times in order to start another MacBook, because I was trying the short that one at the only place I knew; just below the fan ! This is so stupid ! I should have check iFixit before, i should, I should, I should :)

But I learned something. Some things like : I can order ribbons, instead of entire keypads (I have 4 broken ones, now, no... 5 !).

Thanks again, iFixit.

Bu yanıt yardımcı oldu mu?

Puan 1
Yorum Ekle

Yanıtını ekle

Steve sonsuza kadar minnettar olacak.
İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 9

Her zaman: 14,638