Menü

Ayarlarınız

ACER Aspire E1-572-6870 Fan Replacement

Yazan: Cody Lim (ve 2 başka katılımcı)
  • Yorumlar: 1
  • Favoriler: 0
  • Tamamlanma: 3

Zorluk

Zor

Adımlar

15

Gerekli Süre

20 dakika

Bölümler

3

İşaretler

0

Giriş

This guide will teach you how to replace the fan.

Aletler

Bu aletleri satın al

Parçalar

Hiçbir parça belirtilmedi.

  1. Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.

    • Working on your device while it is turned on may result in electric shock. Make sure to shut down and unplug your device before you begin.

    • Flip your laptop over so the back panel is facing upwards and locate the lock switch below the battery.

    Düzenle

  2. Slide the lock switch to the right using your finger or another object. At the same time, grasp the battery with your other hand and begin to slide it upwards.

    • Slide the lock switch to the right using your finger or another object.

    • At the same time, grasp the battery with your other hand and begin to slide it upwards.

    Düzenle

  3. Continue to hold the switch to the right and pull the battery out until it is completely removed.

    • Continue to hold the switch to the right and pull the battery out until it is completely removed.

    • To reinsert or replace the battery, simply line up the tabs on the battery with the laptop and slide it straight back in. There is no need to move the lock switch.

    Düzenle

  4. Remove the 16 2.5 x 8mm Phillips #0 screws from the back panel. Remove the 16 2.5 x 8mm Phillips #0 screws from the back panel.

    • Remove the 16 2.5 x 8mm Phillips #0 screws from the back panel.

    Düzenle

  5. Remove the back panel by carefully disengaging it around the edges and then pull upwards. Remove the back panel by carefully disengaging it around the edges and then pull upwards. Remove the back panel by carefully disengaging it around the edges and then pull upwards.

    • Remove the back panel by carefully disengaging it around the edges and then pull upwards.

    Düzenle

  7. Unscrew the two remaining 2.5 x 8mm Phillips #0 screws from inside the bottom panel as designated in the image.

    • Unscrew the two remaining 2.5 x 8mm Phillips #0 screws from inside the bottom panel as designated in the image.

    Düzenle

  8. Slide out the plastic insert located on the left side, and remove, before returning the laptop to the face-up position. Slide out the plastic insert located on the left side, and remove, before returning the laptop to the face-up position.

    • Slide out the plastic insert located on the left side, and remove, before returning the laptop to the face-up position.

    Düzenle

  9. Carefully flip your laptop back over and open it up. Carefully flip your laptop back over and open it up. Carefully flip your laptop back over and open it up.

    • Carefully flip your laptop back over and open it up.

    Düzenle

  10. Carefully detach the top panel of the laptop and slowly lift it up to reveal the internal components. Carefully detach the top panel of the laptop and slowly lift it up to reveal the internal components. Carefully detach the top panel of the laptop and slowly lift it up to reveal the internal components.

    • Carefully detach the top panel of the laptop and slowly lift it up to reveal the internal components.

    Düzenle

  11. Locate the three ribbons that need to be unplugged, so the two halves of the device may be separated. Unplug the large ribbon by sliding the retainer clip backward (toward the hinges), then gently pulling the cable out of the connector.

    • Locate the three ribbons that need to be unplugged, so the two halves of the device may be separated.

    • Unplug the large ribbon by sliding the retainer clip backward (toward the hinges), then gently pulling the cable out of the connector.

    Düzenle

  12. Remove the other two smaller ribbons by flipping open the small plastic tab that holds the ribbon in the connector. Then simply pull the free ribbon out. Then simply pull the free ribbon out.

    • Remove the other two smaller ribbons by flipping open the small plastic tab that holds the ribbon in the connector.

    • Then simply pull the free ribbon out.

    Düzenle

  13. Lift the top panel all the way up and your laptop is now split into its two distinct halves. Lift the top panel all the way up and your laptop is now split into its two distinct halves.

    • Lift the top panel all the way up and your laptop is now split into its two distinct halves.

    Düzenle

  14. Remove the electrical wiring from its connecting port. Remove the electrical wiring from its connecting port.

    • Remove the electrical wiring from its connecting port.

    Düzenle

  15. Remove the two 2.5 x 8mm Phillips #0 screws holding the fan to the rest of the components.

    • Remove the two 2.5 x 8mm Phillips #0 screws holding the fan to the rest of the components.

    Düzenle

  16. Gently remove fan from its designated spot. Gently remove fan from its designated spot.

    • Gently remove fan from its designated spot.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

3 farklı kişi bu kılavuzu tamamladı.

Yazar

2 tane daha katılımcı ile

Cody Lim

Üyelik tarihi: 25-01-2017

1.245 İtibar

7 adet Kılavuz yazıldı

Rozetler: 12

+9 tane daha rozet

Takım

Cal Poly, Team 9-6, Banghart Winter 2017 Cal Poly, Team 9-6, Banghart Winter 2017 üyesi

CPSU-BANGHART-W17S9G6

3 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 3

Son 30 gün: 21

Her zaman: 974