Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Akai MPK25 Keys Replacement

Yazan: Will Saba (ve 5 başka katılımcı)
  • Yorumlar: 1
  • Favoriler: 2
  • Tamamlanma: 7

Zorluk

Kolay

Adımlar

7

Gerekli Süre

10 dakika

Bölümler

2

İşaretler

1

Featured Student Guide

Öne Çıkan Öğrenci Kılavuzu

Bu kılavuz, çalışkan öğrencilerimizin alın teriyle üretildi ve iFixit kadrosu tarafından epey havalı bulunuyor.

Giriş

Use this guide if any of the keys are broken, chipped, or stuck.

Aletler

Bu aletleri satın al

Parçalar

  1. Remove all the selector knob covers by pulling them off.

    • Remove all the selector knob covers by pulling them off.

    Düzenle

  2. Using needle nose pliers, remove the washers from the four corner selector knobs.

    • Using needle nose pliers, remove the washers from the four corner selector knobs.

    Düzenle

  3. Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

    • Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

    Düzenle

  4. The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

    The Essential Toolkit

    The most helpful tools in our most compact kit.

    Hemen Alışveriş Yapın

  5. Carefully flip the device to the front making sure you secure the face plate and the chassis together. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

    • Carefully flip the device to the front making sure you secure the face plate and the chassis together.

    • Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

    Düzenle

  6. Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

    • Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys.

    • Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

    Düzenle

  7. Using needle nose pliers, grip the top of the spring coil, that is holding down the key, and gently lift the spring away from the key. Using needle nose pliers, grip the top of the spring coil, that is holding down the key, and gently lift the spring away from the key.

    • Using needle nose pliers, grip the top of the spring coil, that is holding down the key, and gently lift the spring away from the key.

    Düzenle

  8. Lift the key from the front of the keyboard towards the back in order to remove it completely.

    • Lift the key from the front of the keyboard towards the back in order to remove it completely.

    Düzenle
Sonuç

To reassemble the keyboard and close up the case, follow these instructions in reverse order.

7 farklı kişi bu kılavuzu tamamladı.

Yazar

5 tane daha katılımcı ile

Will Saba

Üyelik tarihi: 11-01-2013

376 İtibar

2 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Takım

Cal Poly, Team 20-6, Maness Winter 2013 Cal Poly, Team 20-6, Maness Winter 2013 üyesi

CPSU-MANESS-W13S20G6

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 3

Son 7 gün: 27

Son 30 gün: 115

Her zaman: 8,909