Giriş

Use this guide if any of the selector knobs get bent, broken, or stops working.

Remove all the selector knob covers by pulling them off.
  • Remove all the selector knob covers by pulling them off.

Yorum Ekle

Using needle nose pliers, remove the washers from the four corner selector knobs.
  • Using needle nose pliers, remove the washers from the four corner selector knobs.

Yorum Ekle

Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.
  • Flip the device over. Using a Philips #2 screw driver, remove the fourteen 10.3 mm black screws holding the back panel in place.

Yorum Ekle

Carefully flip the device to the front making sure you secure the face plate and the chassis together. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides. Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.
  • Carefully flip the device to the front making sure you secure the face plate and the chassis together.

  • Please use care in following the step above to avoid ripping the ribbon cables connecting the two sides.

Yorum Ekle

Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged. Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.
  • Rotate the device 180 degrees and carefully remove the face plate by slightly lifting the screen side towards you and then sliding the bottom out from under the keys.

  • Use care when doing the step above so that the ribbon connectors which connect the top of the chassis to the top of the face plate are not damaged.

Yorum Ekle

Using a Phillips #2 screwdriver, remove the thirteen 9.8mm silver screws holding the mother board to the face plate.
  • Using a Phillips #2 screwdriver, remove the thirteen 9.8mm silver screws holding the mother board to the face plate.

Yorum Ekle

Using two plastic opening tools, slide the black locking mechanism on the ZIF connector towards you. This will remove the ribbon cable connecting the motherboard to the screen. Using two plastic opening tools, slide the black locking mechanism on the ZIF connector towards you. This will remove the ribbon cable connecting the motherboard to the screen.
  • Using two plastic opening tools, slide the black locking mechanism on the ZIF connector towards you. This will remove the ribbon cable connecting the motherboard to the screen.

Yorum Ekle

Wiggle and pull out the ribbon cable connecting the mother board to the beat pads. Wiggle and pull out the ribbon cable connecting the mother board to the beat pads.
  • Wiggle and pull out the ribbon cable connecting the mother board to the beat pads.

Yorum Ekle

Remove the mother board completely from the face plate and identify the broken potentiometer. Remove the mother board completely from the face plate and identify the broken potentiometer. Remove the mother board completely from the face plate and identify the broken potentiometer.
  • Remove the mother board completely from the face plate and identify the broken potentiometer.

Yorum Ekle

Flip the mother board back over so the potentiometers are facing down and the leads are facing up. Then identify which leads correspond to the broken potentiometer.
  • Flip the mother board back over so the potentiometers are facing down and the leads are facing up. Then identify which leads correspond to the broken potentiometer.

  • Use a soldering iron with solder wick (or a solder sucker) in order to free the potentiometer from the mother board.

  • Add some leaded solder to the leads if your having trouble getting the factory solder to draw to the solder wick.

What is the model of encoder or part number that works for this repair?

Zachary Hatsis - Yanıt

Sonuç

To reassemble your device, follow these instructions in reverse order.

3 başka kişi bu kılavuzu tamamladı.

Anthony Zepeda

Üyelik tarihi: 30-01-2013

210 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team 20-6, Maness Winter 2013 Cal Poly, Team 20-6, Maness Winter 2013 üyesi

CPSU-MANESS-W13S20G6

5 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 3

Son 7 Gün: 8

Son 30 Gün: 33

Her zaman: 2,071