Astak Mole Motherboard Replacement - iFixit Tamir Kılavuzu

Onarım Topluluğuna Katılın - Hesap Oluşturun

Giriş

In order to replace the motherboard, you are going to have to access it first. After that, you will have to separate everything from the old motherboard and reconnect everything to the new motherboard.

Neye ihtiyacın var

1. Adım 1 Lower Case
  Remove the four bottom tabs in order to access the bottom screws.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
2. Adım 2
  Remove all four 14 mm Phillips #1 screws.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
3. Adım 3
  Remove the SD card.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
5. Adım 4
  Pry up the motherboard on the four points using a spudger.
  
  The regular black nylon spudger should be used whenever possible, especially around sensitive internal components.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
6. Adım 5
  Gently pull back the motherboard to expose many of the component's wired connections.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
1. Adım 6 Motherboard
  Sever the indicated adhesive connections to the motherboard allowing the wired connections to be removed.
  
  All wired connections to the motherboard are removed by the thin plastic male connector inserted into the larger female plastic connection.
  
  The regular black nylon spudger should be used whenever possible, especially around sensitive internal components.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
2. Adım 7
  The red wires may be adhered to the CPU as indicated and will need to be severed as shown.
  
  Be careful not to scratch the CPU in this step. This is not a wired connection.
  
  Sever the additional adhesive connections so that the wired connections may be removed.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
3. Adım 8
  Locate and unscrew the indicated screw using the (PH1) Phillips head bit.
  
  Screw Measurements: (Length= 5.3mm)
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024
4. Adım 9
  Remove the last two wired connections to the motherboard by severing the indicated connections.
  
  Lift up the secondary motherboard as indicated using the metal spudger.
  
  All connections should be severed from the motherboard and a new motherboard may be inserted.
  
  It is advised to reapply adhesive to wired connections during reassembly.
  Düzenle
  
  FixBot'a Sor
  
  Yorum Ekle
  
  1024

Sonuç

To reassemble your device, follow these instructions in reverse order.

İptal et: Bu kılavuzu tamamlamadım.

Yazar

5 tane daha katılımcı ile

Andrew Birch

Üyelik tarihi: 09/15/16

204 İtibar

2 adet Kılavuz yazıldı

+5 tane daha rozet

Ekip

USF Tampa, Team 2-2, Blackwell Fall 2016 USF Tampa, Team 2-2, Blackwell Fall 2016 üyesi

USFT-BLACKWELL-F16S2G2

4 Üyeler

12 adet Kılavuz yazıldı

0Kılavuz Yorumları

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 8

Son 30 gün: 30

Her zaman: 941