Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Giriş

Use this guide to replace a trackpad on your Asus Chromebook C300SA-DS02 that has stopped registering input or registers incorrect input. The trackpad is a part of the keyboard assembly and is fairly easy to access.

  1. Power the laptop off and make sure the charger is unplugged before starting. Remove the eight 8.0mm Phillips #0 screws on the bottom of the laptop.
    • Power the laptop off and make sure the charger is unplugged before starting.

    • Remove the eight 8.0mm Phillips #0 screws on the bottom of the laptop.

    • Remove the three 6.0mm Phillips #0 screws.

  2. Open the laptop. Using an iFixit opening tool, pry along the edges of the keyboard. Lift the keyboard and slide it gently towards you.
    • Open the laptop.

    • Using an iFixit opening tool, pry along the edges of the keyboard.

    • Lift the keyboard and slide it gently towards you.

    • Do not completely remove the keyboard. It is still connected to the back panel by a pair of ribbon cables.

  3. Disconnect the two ZIF connectors by prying up the locking bar with a spudger and removing the ribbon cable. Disconnect the two ZIF connectors by prying up the locking bar with a spudger and removing the ribbon cable. Disconnect the two ZIF connectors by prying up the locking bar with a spudger and removing the ribbon cable.
    • Disconnect the two ZIF connectors by prying up the locking bar with a spudger and removing the ribbon cable.

  4. Remove the keyboard from the laptop.
    • Remove the keyboard from the laptop.

  5. Flip over the keyboard assembly to reveal the trackpad beneath. Flip over the keyboard assembly to reveal the trackpad beneath.
    • Flip over the keyboard assembly to reveal the trackpad beneath.

  6. Peel up the two pieces of foil tape holding down the trackpad. Peel up the two pieces of foil tape holding down the trackpad.
    • Peel up the two pieces of foil tape holding down the trackpad.

  7. Use a spudger to release the locking bar of the ZIF connector near the center of the trackpad. Slide the cable ribbon from the connector. Slide the cable ribbon from the connector.
    • Use a spudger to release the locking bar of the ZIF connector near the center of the trackpad.

    • Slide the cable ribbon from the connector.

  8. Peel back the ribbon cable, which is adhered to the trackpad.
    • Peel back the ribbon cable, which is adhered to the trackpad.

  9. Remove the four 2.5mm Phillips #0 screws along the top edge of the trackpad. Remove the four 2.5mm Phillips #0 screws along the top edge of the trackpad. Remove the four 2.5mm Phillips #0 screws along the top edge of the trackpad.
    • Remove the four 2.5mm Phillips #0 screws along the top edge of the trackpad.

  10. Pry the trackpad from the top edge with a finger or spudger. Lift the trackpad up and away from the keyboard assembly.
    • Pry the trackpad from the top edge with a finger or spudger.

    • Lift the trackpad up and away from the keyboard assembly.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Austin Blakely

Üyelik tarihi: 11-03-2019

7.890 İtibar

46 adet Kılavuz yazıldı

Takım

iFixit iFixit üyesi

Community

134 Üyeler

14.939 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 101