Slide the battery's locking tabs from the locked position to unlocked positions. The right tab is unlocked when a red dot is showing. The left tab will have to be held in the unlocked position in order to release the battery.
  • Slide the battery's locking tabs from the locked position to unlocked positions.

    • The right tab is unlocked when a red dot is showing.

    • The left tab will have to be held in the unlocked position in order to release the battery.

Yorum Ekle

Slide the battery out while holding the left locking tab in the unlocked position.
  • Slide the battery out while holding the left locking tab in the unlocked position.

Yorum Ekle

Caution Follow this step to detach the upper portion of the keyboard, but do not remove it from the laptop. Damage to the keyboard's ribbon cable may result if improperly executed. Identify the three metal tabs holding down the laptop's keyboard.
  • Caution Follow this step to detach the upper portion of the keyboard, but do not remove it from the laptop. Damage to the keyboard's ribbon cable may result if improperly executed.

  • Identify the three metal tabs holding down the laptop's keyboard.

  • Using a spudger, depress each metal tab to remove the keyboard.

    • The upper part of the keyboard should "pop up" from its holder.

Yorum Ekle

Clips hold the bottom portion of the keyboard to the laptop. Gently lift the upper portion of the keyboard and then move the entire keyboard towards the computer's screen until the ribbon cable is visible. Clips hold the bottom portion of the keyboard to the laptop. Gently lift the upper portion of the keyboard and then move the entire keyboard towards the computer's screen until the ribbon cable is visible.
  • Clips hold the bottom portion of the keyboard to the laptop. Gently lift the upper portion of the keyboard and then move the entire keyboard towards the computer's screen until the ribbon cable is visible.

Yorum Ekle

Using a spudger, gently push the two black pins holding the ribbon cable towards the computer's screen.
  • Using a spudger, gently push the two black pins holding the ribbon cable towards the computer's screen.

  • Slide the keyboard's ribbon cable from the connector.

Yorum Ekle

Remove the keyboard by lifting upwards.
  • Remove the keyboard by lifting upwards.

Yorum Ekle

Mac RAM Kitleri
Mac'inizi hızlandırın. Hafızasını en yükseğe çıkar.
Mac RAM Kitleri
Mac'inize daha fazla bellek alın.
Remove the nine 4.76mm Phillips #0 screws on the top cover of the laptop. Remove the nine 4.76mm Phillips #0 screws on the top cover of the laptop.
  • Remove the nine 4.76mm Phillips #0 screws on the top cover of the laptop.

Yorum Ekle

Remove the six 4.76 mm Phillips #0 screws on the back of the laptop. Remove the six 4.76 mm Phillips #0 screws on the back of the laptop.
  • Remove the six 4.76 mm Phillips #0 screws on the back of the laptop.

Yorum Ekle

Flip the laptop back over and identify the touchpad ribbon. Unlock the tan locking pin from the black connector by pushing the pin to the right with a spudger. Unlock the tan locking pin from the black connector by pushing the pin to the right with a spudger.
  • Flip the laptop back over and identify the touchpad ribbon.

  • Unlock the tan locking pin from the black connector by pushing the pin to the right with a spudger.

Yorum Ekle

Slide out the touchpad's ribbon connector by pulling the blue tab to the right.
  • Slide out the touchpad's ribbon connector by pulling the blue tab to the right.

Yorum Ekle

Use a plastic opening tool to gently detach the top cover from the laptop's base. See the next step for removing the cover.
  • Use a plastic opening tool to gently detach the top cover from the laptop's base. See the next step for removing the cover.

Yorum Ekle

Caution: You will need to clear the audio and microphone jacks by lifting the right half and then moving the cover to the left (as shown in the second picture) to prevent damaging the cover. Remove the laptop cover. Remove the laptop cover.
  • Caution: You will need to clear the audio and microphone jacks by lifting the right half and then moving the cover to the left (as shown in the second picture) to prevent damaging the cover.

  • Remove the laptop cover.

Yorum Ekle

Remove the large black wire using a plastic opening tool. Remove the large black wire using a plastic opening tool. Remove the large black wire using a plastic opening tool.
  • Remove the large black wire using a plastic opening tool.

Yorum Ekle

Gently pry off the six rubber covers around the outside of the screen using a 2 mm flat head screwdriver. A flat head screwdriver is preferable over a spudger as the spudger's head is not thin enough to to slip under the rubber covers. Remove the six 4.76 mm Phillips #0 screws underneath each cover.
  • Gently pry off the six rubber covers around the outside of the screen using a 2 mm flat head screwdriver.

    • A flat head screwdriver is preferable over a spudger as the spudger's head is not thin enough to to slip under the rubber covers.

  • Remove the six 4.76 mm Phillips #0 screws underneath each cover.

Yorum Ekle

Using a plastic opening tool, carefully detach the casing around the screen cover.
  • Using a plastic opening tool, carefully detach the casing around the screen cover.

    • Remove the screen cover.

Yorum Ekle

Remove the four 4.76mm Phillips #0 screws located on the corners of the screen. Lift out the display screen. Lift out the display screen.
  • Remove the four 4.76mm Phillips #0 screws located on the corners of the screen.

  • Lift out the display screen.

Yorum Ekle

Detach the small white plug located to the left of the webcam with a spudger. It may be helpful to hold down the webcam unit with a finger. It may be helpful to hold down the webcam unit with a finger.
  • Detach the small white plug located to the left of the webcam with a spudger.

    • It may be helpful to hold down the webcam unit with a finger.

Yorum Ekle

Carefully lift the webcam off of its placeholders starting from the left side.
  • Carefully lift the webcam off of its placeholders starting from the left side.

    • There may be a small amount of adhesive attached to the back of the webcam. Use the end of a spudger to carefully remove the adhesive.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Michael Barker

Üyelik tarihi: 25-01-2012

254 İtibar

4 adet Kılavuz yazıldı

Takım

Cal Poly, Team 3-27, Amido Winter 2012 Cal Poly, Team 3-27, Amido Winter 2012 üyesi

CPSU-AMIDO-W12S3G27

4 Üyeler

16 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 2

Son 30 Gün: 19

Her zaman: 7,979