Eşyalarını Tamir Et Topluluk Mağaza

Axess TA2513-10WT Speaker Replacement

Giriş

In this guide you will find steps on how to remove the speakers from the Axess TA2513-10WT tablet in order to replace them. The guide will show you how to access the tablet's circuit board, identify the right and left speakers, and how to remove the speakers from the circuit board.

Neye ihtiyacın var

  1. Axess TA2513-10WT Speaker Replacement, Back Cover: adım 1, 1 resimden 1.

    • Lay the tablet down on a flat surface with the screen facing up, and the external camera facing upwards and closest to you.

    Düzenle

  2. Axess TA2513-10WT Speaker Replacement: adım 2, 3 resimden 1. Axess TA2513-10WT Speaker Replacement: adım 2, 3 resimden 2. Axess TA2513-10WT Speaker Replacement: adım 2, 3 resimden 3.

    • Insert the plastic opening tool in the space between the screen and the back cover above the volume buttons.

    • Slide the plastic opening tool gently along the sides.

    • If a small gap is not created between the screen and the back cover, pry gently upward at each of these latching points.

    Düzenle

  3. Axess TA2513-10WT Speaker Replacement: adım 3, 1 resimden 1.

    • Place the spudger in an open space to keep the back case from shutting while you continue to slide the opening tool.

    Düzenle

  4. Axess TA2513-10WT Speaker Replacement: adım 4, 1 resimden 1.

    • Remove the back cover with your hands once all points have been unlatched. It should separate completely from the screen that contains the battery and chip components.

    Düzenle

  6. Axess TA2513-10WT Speaker Replacement, Speaker: adım 5, 1 resimden 1.

    • Remove tape attached to black and red speaker wires.

    Düzenle

  7. Axess TA2513-10WT Speaker Replacement: adım 6, 1 resimden 1.

    • Identify the four speaker nodes.

    • From left to right the nodes are "SPKP1", "SPKN1", "LN", and "LP"

    Düzenle

  8. Axess TA2513-10WT Speaker Replacement: adım 7, 1 resimden 1.

    • Place the soldering tool on the speaker node labeled "SPKP1" and quickly remove the red wire with tweezers.

    Düzenle

  9. Axess TA2513-10WT Speaker Replacement: adım 8, 1 resimden 1.

    • Place the soldering tool on the speaker node labeled "SPKN1" and quickly remove the black wire with tweezers.

    Düzenle

  10. Axess TA2513-10WT Speaker Replacement: adım 9, 1 resimden 1.

    • Place the soldering tool on the speaker node labeled "LP" and quickly remove the black wire with the tweezers.

    Düzenle

  11. Axess TA2513-10WT Speaker Replacement: adım 10, 1 resimden 1.

    • Place the soldering tool on the speaker node labeled "LN" and quickly remove the red wire with tweezers.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

7 tane daha katılımcı ile

Steven Kavanagh

Üyelik tarihi: 03/24/15

301 İtibar

3 adet Kılavuz yazıldı

Rozetler: 3

Ekip

Baylor, Team 6-3, Shaver Spring 2015 Baylor, Team 6-3, Shaver Spring 2015 üyesi

BU-SHAVER-S15S6G3

3 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 3

Son 30 gün: 3

Her zaman: 302