Eşyalarını Tamir Et Topluluk Mağaza

BEM Mojo 2 Speaker Replacement

Giriş

This guide will show you how to replace the speaker itself but before doing so, check to make sure your Bluetooth signal is not being obstructed by any objects or walls and is close enough to the speaker. Also, make sure the battery is fully charged. Both of these could be causing distorted sound on your speaker. If both of these possible causes are not true than the actual cause could have to do with your speaker in which you should replace it.

Neye ihtiyacın var

  1. BEM Mojo 2 Speaker Replacement, Speaker Battery: adım 1, 1 resimden 1.

    • Pull back the rubber corners to uncover the bottom screws.

    • Continue this process for all four 10 mm screws.

    Düzenle

  2. BEM Mojo 2 Speaker Replacement: adım 2, 1 resimden 1.

    • Use the J0 screwdriver to remove all four 10mm screws from the bottom of the speaker.

    • Caution: It is important when using the screwdriver to not use excessive force as this may strip the screw and can damage the speaker itself.

    Düzenle

  3. BEM Mojo 2 Speaker Replacement: adım 3, 1 resimden 1.

    • Remove the bottom cover of the speaker.

    • Caution: Be careful when removing the bottom cover of the speaker as there are wires that connect to the speaker itself that become exposed upon base removal.

    • Remove all of the wires from the speakers internal chip, utilizing the tweezers.

    • Caution: Be careful not to damage the chip.

    Düzenle

  4. BEM Mojo 2 Speaker Replacement: adım 4, 1 resimden 1.

    • Remove the speakers battery from its metal base, utilizing the plastic opening tool.

    Düzenle

  6. BEM Mojo 2 Speaker Replacement: adım 5, 1 resimden 1.

    • Remove the wires from the speakers battery using the tweezers or by gently removing them by lightly pinching.

    Düzenle

  7. BEM Mojo 2 Speaker Replacement, Speaker Motherboard: adım 6, 1 resimden 1.

    • Use the J0 screwdriver to remove all four 10mm screws from the motherboard.

    Düzenle

  8. BEM Mojo 2 Speaker Replacement: adım 7, 1 resimden 1.

    • Remove the red/black wires in addition to the blue/white wires using the tweezers.

    Düzenle

  9. BEM Mojo 2 Speaker Replacement: adım 8, 1 resimden 1.

    • Remove bus wire from the speaker's motherboard and lift the motherboard out of the speaker.

    Düzenle

  10. BEM Mojo 2 Speaker Replacement, Speaker: adım 9, 1 resimden 1.

    • Remove any glue that is left over from previous parts that may be covering the screw holes or the speakers drive.

    Düzenle

  11. BEM Mojo 2 Speaker Replacement: adım 10, 2 resimden 1. BEM Mojo 2 Speaker Replacement: adım 10, 2 resimden 2.

    • Remove the speaker's four 10 mm base screws.

    Düzenle

  12. BEM Mojo 2 Speaker Replacement: adım 11, 2 resimden 1. BEM Mojo 2 Speaker Replacement: adım 11, 2 resimden 2.

    • Pry out the speaker's base using the metal Spuger. Use caution upon this step, it will require the use of force.

    • Remove the wire that will be placed in the speakers driver hole for access to the speaker.

    Düzenle

  13. BEM Mojo 2 Speaker Replacement: adım 12, 2 resimden 1. BEM Mojo 2 Speaker Replacement: adım 12, 2 resimden 2.

    • Remove the speaker's two 10 mm screws that are located in its base then take the driver out of the speaker.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

2 tane daha katılımcı ile

Rachel Iacoboni

Üyelik tarihi: 01/30/18

618 İtibar

5 adet Kılavuz yazıldı

Rozetler: 7

+4 tane daha rozet

Ekip

Baylor, Team S1-G1, Johnson Spring 2018 Baylor, Team S1-G1, Johnson Spring 2018 üyesi

BU-JOHNSON-S18S1G1

3 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 2

Son 7 gün: 5

Son 30 gün: 6

Her zaman: 350