Menü

Ayarlarınız

Black and Decker TR1278B Bread Grabber Spring Replacement

Yazan: Brea-Monique (ve 3 başka katılımcı)
  • Yorumlar: 3
  • Favoriler: 0

Zorluk

Orta

Adımlar

9

Gerekli Süre

Bir süre öner??

Bölümler

2

İşaretler

2

Action Shots

İşlem Görüntüleri

Öykünün yıldızı olun! Belirli eylemlerin nasıl gerçekleştirileceğini daha iyi göstermek için bu kılavuza resimler gerekli.

Needs More Images

Daha Fazla Görsel Gerekli

Biraz daha fazla görsel sayesinde bu kılavuzdaki prosedürler apaçık olacaktır.

Giriş

This is a replacement guide for the bread grabber springs on the Black and Decker TR1278B.

  1. Unplug the toaster before disassembly.

    • Unplug the toaster before disassembly.

    • Remove the carriage lever by pulling it away from the toaster.

    Düzenle

  2. Toaster will be turned upside down. Clear crumb tray or work over a paper towel.

    • Toaster will be turned upside down. Clear crumb tray or work over a paper towel.

    • Turn the toaster upside down.

    • Unscrew all four 4mm screws on the bottom using a Phillip's head #2 (PH2) screwdriver.

    Düzenle

  3. Detach the bottom from the front cover using the plastic opening tool.

    • Detach the bottom from the front cover using the plastic opening tool.

    Düzenle

  5. Turn the toaster right side up.

    • Turn the toaster right side up.

    • Support the bottom. The ribbon cable that connects the toaster to the front cover can be damaged.

    • Lift the front cover.

    • Lift carefully. Again the ribbon cable can be damaged.

    Düzenle

  6. Detach the bundled cable connector from the toaster by carefully pulling it away from the circuit board.

    • Detach the bundled cable connector from the toaster by carefully pulling it away from the circuit board.

    Düzenle

  7. Locate the spring

    • Locate the spring

    Düzenle

  8. Press down on the toaster lever to gain access to the grabber spring located behind the large metal plate.

    • Press down on the toaster lever to gain access to the grabber spring located behind the large metal plate.

    • Use metal spudger to loosen clamps on spring.

    Düzenle

  9. Use needle nose tweezers to pull the spring off of its hook.

    • Use needle nose tweezers to pull the spring off of its hook.

    • Repeat this step for the opposite side.

    Düzenle

  10. Remove the old spring from the toaster unit to insert the new one.

    • Remove the old spring from the toaster unit to insert the new one.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

3 tane daha katılımcı ile

Brea-Monique

Üyelik tarihi: 15-02-2017

321 İtibar

3 adet Kılavuz yazıldı

Rozetler: 7

+4 tane daha rozet

Takım

USF Tampa, Team 8-1, Eyestone Spring 2017 USF Tampa, Team 8-1, Eyestone Spring 2017 üyesi

USFT-EYESTONE-S17S8G1

3 Üyeler

5 adet Kılavuz yazıldı

0 Comments

Yorum Ekle

Yorum Ekle

İstatistikleri Görüntüle:

Past 24 Hours: 1

Past 7 Days: 5

Past 30 Days: 13

Her zaman: 502