Giriş

This guide was written to aid with Blackberry Curve screen replacement. Following the steps below should provide relatively simple means of achieving this goal.

Place your Blackberry face down in front of you.
  • Place your Blackberry face down in front of you.

Yorum Ekle

Locate the indent on the bottom of the back cover.
  • Locate the indent on the bottom of the back cover.

  • Use your fingernail to lift and remove the back cover.

Yorum Ekle

From the top, use your fingernail to lift and remove the battery.
  • From the top, use your fingernail to lift and remove the battery.

Yorum Ekle

Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
  • Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.

Yorum Ekle

Place the phone face up and use tweezers to securely grip and lift the screen upwards. Place the phone face up and use tweezers to securely grip and lift the screen upwards.
  • Place the phone face up and use tweezers to securely grip and lift the screen upwards.

Yorum Ekle

Use your prying tool to lift the bottom edge of the front cover.
  • Use your prying tool to lift the bottom edge of the front cover.

Yorum Ekle

Use your nails to unclip sides of frame from the phone.
  • Use your nails to unclip sides of frame from the phone.

Yorum Ekle

Lift and remove frame.
  • Lift and remove frame.

Yorum Ekle

Lift and remove keyboard.
  • Lift and remove keyboard.

Yorum Ekle

Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver
  • Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver

Yorum Ekle

Carefully pull keyboard base up and away from phone.
  • Carefully pull keyboard base up and away from phone.

  • Disconnect keyboard base from phone completely.

Yorum Ekle

Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver
  • Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver

Yorum Ekle

Using a prying tool, find the crease below the screen. Insert where shown and use the tool to unclip the two sides of screen from body.
  • Using a prying tool, find the crease below the screen.

  • Insert where shown and use the tool to unclip the two sides of screen from body.

    • Prying tool goes approximately midway between the top and bottom edge of the screen.

Yorum Ekle

From back of the phone, use finger to push the front piece of the phone away from the back piece. From back of the phone, use finger to push the front piece of the phone away from the back piece.
  • From back of the phone, use finger to push the front piece of the phone away from the back piece.

Yorum Ekle

Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone. Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone. Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone.
  • Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

8 başka kişi bu kılavuzu tamamladı.

Alek Squires

Üyelik tarihi: 30-09-2013

415 İtibar

2 adet Kılavuz yazıldı

Takım

Cal Poly, Team 14-7, Forte Fall 2013 Cal Poly, Team 14-7, Forte Fall 2013 üyesi

CPSU-FORTE-F13S14G7

5 Üyeler

5 adet Kılavuz yazıldı

Bir Yorum

would appreciate new ldc part # and order info! - - !

Donald Burgo - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 7

Son 30 Gün: 28

Her zaman: 3,589