Ana içeriğe geç

What you need

  1. Boosted Board 1st Generation Skateboard Bearings Replacement, Rear Wheels: adım 1, 2 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement, Rear Wheels: adım 1, 2 resimden 2.
    • Loosen the two 16.74 mm motor mount hex nut screws with a 9/64" Allen wrench.

    • Do Not Remove the Screws.

  2. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 2, 1 resimden 1.
    • Compress the motor mount back towards the wheel.

    • While keeping the motor mount compressed, tighten one of the hex nuts that you loosened in the previous step.

    • The motor mounts are spring tensioned so it is necessary compress them to loosen the belts.

  3. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 3, 2 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 3, 2 resimden 2.
    • Remove the axel nut with a 1/2" socket wrench

  4. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 4, 3 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 4, 3 resimden 2. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 4, 3 resimden 3.
    • Rotate and pull counterclockwise until the wheel comes off the axle completely.

    • The front washer will come off with the wheel.

    • Remove the back washer from the axle.

    • Replacing the wheel requires the bearings to be switched into the new wheel.

  5. Boosted Board 1st Generation Skateboard Bearings Replacement, Skateboard Bearings: adım 5, 2 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement, Skateboard Bearings: adım 5, 2 resimden 2.
    • Use one finger to pull out the pulley bearing.

    • A good technique is to go around in a circle and lift from underneath the bearing in a carving motion.

  6. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 6, 3 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 6, 3 resimden 2. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 6, 3 resimden 3.
    • Use an Allen wrench to apply pressure to the inside edge of the bearing until it pops out

  7. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 7, 3 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 7, 3 resimden 2. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 7, 3 resimden 3.
    • Replace bearing by dropping it in the center of the wheel and use a socket wrench to pop in back it place

  8. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 8, 3 resimden 1. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 8, 3 resimden 2. Boosted Board 1st Generation Skateboard Bearings Replacement: adım 8, 3 resimden 3.
    • Slide the bearing spacer on to an Allen wrench

    • Align the Allen wrench in the center of the bearing and drop the spacer directly in the middle

    • Repeat Step 7 for placing the bearing in this side of the wheel.

Sonuç

To reassemble your device, follow these directions in reverse order.

Emily Imfeld

Üyelik tarihi: 06-10-2016

514 İtibar

4 adet Kılavuz yazıldı

Team

Cal Poly, Team 15-7, Livingston Fall 2016 Cal Poly, Team 15-7, Livingston Fall 2016 üyesi

CPSU-LIVINGSTON-F16S15G7

4 Üyeler

6 adet Kılavuz yazıldı

0 Comments

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 4

Her zaman: 660