Eşyalarını Tamir Et Topluluk Mağaza

Bottom Board Removal

Neye ihtiyacın var

  1. Bottom Board Removal, Engage Wired Optical Mouse Top and Outer Shell Removal: adım 1, 1 resimden 1.

    • Flip the mouse over and peel off the stickers on the perimeter of the bottom of the mouse.

    Düzenle

  2. Bottom Board Removal: adım 2, 1 resimden 1.

    • Use the Phillips #1 screwdriver to remove four 5 mm screws from the bottom of the mouse.

    • Use the Phillips #1 screwdriver to remove the two 9 mm screws from the bottom of the mouse.

    Düzenle

  3. Bottom Board Removal: adım 3, 3 resimden 1. Bottom Board Removal: adım 3, 3 resimden 2. Bottom Board Removal: adım 3, 3 resimden 3.

    • Grab the top shell of the mouse and lift up to remove.

    Düzenle

  4. Bottom Board Removal: adım 4, 1 resimden 1.

    • The capacitors on this board can release stored electrical energy if touched.

    • Touch your capacitor discharge tool to the capacitor leads on the board to release the stored energy. If leads are inaccessible, wait until you've removed the board from the mouse body.

    Düzenle

  6. Bottom Board Removal: adım 5, 2 resimden 1. Bottom Board Removal: adım 5, 2 resimden 2.

    • Use a spudger to pry underneath the white plug and pop it out to disconnect the upper board from the lower board.

    Düzenle

  7. Bottom Board Removal, Side Panels: adım 6, 2 resimden 1. Bottom Board Removal, Side Panels: adım 6, 2 resimden 2.

    • Locate the 5 mm silver flat head mounting screws (2) to the left and right of the scroll wheel and remove with the Phillips #1 screwdriver.

    Düzenle

  8. Bottom Board Removal: adım 7, 2 resimden 1. Bottom Board Removal: adım 7, 2 resimden 2.

    • Locate the snaps on the bottom corners of the mouse side panels and pop the indicated snaps out, using a spudger or your fingernail.

    Düzenle

  9. Bottom Board Removal: adım 8, 3 resimden 1. Bottom Board Removal: adım 8, 3 resimden 2. Bottom Board Removal: adım 8, 3 resimden 3.

    • Repeat Step 6 for the opposite side panel in order to detach both sides from the base of the mouse.

    Düzenle

  10. Bottom Board Removal: adım 9, 2 resimden 1. Bottom Board Removal: adım 9, 2 resimden 2.

    • Grab the sides of the mouse and lift them up to detach from the base of the mouse.

    Düzenle

  11. Bottom Board Removal, Bottom Board: adım 10, 2 resimden 1. Bottom Board Removal, Bottom Board: adım 10, 2 resimden 2.

    • Pop the scroll wheel out of the snap holding it in place. You can use your finger or a spudger to do so.

    Düzenle

  12. Bottom Board Removal: adım 11, 2 resimden 1. Bottom Board Removal: adım 11, 2 resimden 2.

    • Locate the four 5 mm black flat head screws on the corners of the bottom board.

    • Unscrew these four black screws.

    Düzenle

  13. Bottom Board Removal: adım 12, 3 resimden 1. Bottom Board Removal: adım 12, 3 resimden 2. Bottom Board Removal: adım 12, 3 resimden 3.

    • Lift the bottom board up to remove from its mounting posts. This will separate it completely from the bottom panel of the mouse.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

3 tane daha katılımcı ile

royceeklund

Üyelik tarihi: 01/18/13

79 İtibar

3 adet Kılavuz yazıldı

Rozetler: 9

+6 tane daha rozet

Ekip

Cal Poly, Team 18-36, Regan Winter 2013 Cal Poly, Team 18-36, Regan Winter 2013 üyesi

CPSU-REGAN-W13S18G36

3 Üyeler

30 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 6

Son 30 gün: 26

Her zaman: 5,160