Ana içeriğe geç

Giriş

The audio jack is not used for audio, but for streaming setup data from your phone to the Canary, so it is very important to replace if damaged.

Once you remove the bottom casing and Ethernet PCB board, the audio and USB PCB board becomes accessible. Remember to pull on the power connector itself and not the wires to avoid damage.

If either the audio jack or USB type C connector are damaged, this guide will show you how to replace the board.

A Phillips #0 screwdriver can be used for both screws.

Parçalar

Hiçbir parça belirtilmedi.

  1. Canary CAN100USBK Audio and USB PCB Board Replacement, Bottom Casing: adım 1, 2 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement, Bottom Casing: adım 1, 2 resimden 2.
    • Grip the rubber ring with your fingers and pull up.

    • Rotate the Canary as you pull out one tab at a time.

  2. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 2, 1 resimden 1.
    • Use your Phillips #0 screwdriver to remove the four 6mm screws.

  3. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 3, 3 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 3, 3 resimden 2. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 3, 3 resimden 3.
    • Use the flat end of the spudger to carefully pry off the bottom casing.

    • Alternate pushing up on the left and right sides until the clips holding the case in are visible.

  4. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 4, 2 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 4, 2 resimden 2.
    • Do not yank the bottom off or you may damage the ribbon cable or the ZIF connector.

    • Carefully remove the bottom casing by gripping it on both sides and pulling straight up.

  5. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 5, 2 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 5, 2 resimden 2.
    • Use the pointed end of the spudger to flip up the small retaining flap on the ZIF (zero insertion force) connector.

    • Pull the ribbon cable out towards the device.

  6. Canary CAN100USBK Audio and USB PCB Board Replacement, Ethernet PCB Board: adım 6, 1 resimden 1.
    • Use your Phillips #0 screwdriver to remove the three 5mm screws.

  7. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 7, 2 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 7, 2 resimden 2.
    • Place the flat end of the spudger underneath the Ethernet PCB board and slowly pry up until it's loose.

  8. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 8, 1 resimden 1.
    • Carefully pull the Ethernet PCB board away from the board that sits underneath.

  9. Canary CAN100USBK Audio and USB PCB Board Replacement, Audio and USB PCB Board: adım 9, 1 resimden 1.
    • Using your fingernails, wiggle the power connector back and forth until it becomes loose.

    • Pull the power connector straight out of the socket.

    • Pull only on the power connector and not the wires themselves to prevent damage.

  10. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 10, 3 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 10, 3 resimden 2. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 10, 3 resimden 3.
    • Use the spudger to pry up the retaining flap of the ZIF connector.

    • Disconnect the ribbon cable.

  11. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 11, 1 resimden 1.
    • Remove the two Phillips #0 5mm screws.

  12. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 12, 2 resimden 1. Canary CAN100USBK Audio and USB PCB Board Replacement: adım 12, 2 resimden 2.
    • Pull the board away from the bottom casing by lifting the end closest to the chimney up.

Sonuç

To reassemble your device, follow these instructions in reverse order.

3 farklı kişi bu kılavuzu tamamladı.

Kristopher Gates

Üyelik tarihi: 28-02-2017

399 İtibar

3 adet Kılavuz yazıldı

Team

USF Tampa, Team S1-G2, Nance Spring 2017 USF Tampa, Team S1-G2, Nance Spring 2017 üyesi

USFT-NANCE-S17S1G2

4 Üyeler

16 adet Kılavuz yazıldı

2 Comments

Hello great tutorial I have a problem with the usb on mine.

Where did you buy the PCB from?

craig perrin - Yanıt

nice guide, need to buy the ep-cnc01bb-02 board which has the micro usb on it as mine is worn out... any ideas?

Billy - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 1

Son 30 gün: 6

Her zaman: 629