Ana içeriğe geç

What you need

  1. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove the eyepiece cap: adım 1, 2 resimden 1. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove the eyepiece cap: adım 1, 2 resimden 2.
    • Pull up on both sides of the the eyepiece cap. It should come off with little pressure.

  2. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove screws from under the eyepiece cap: adım 2, 1 resimden 1.
    • Remove the two screws hidden under the viewfinder eyepiece cap.

  3. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove hidden screw and other visible screw: adım 3, 3 resimden 1. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove hidden screw and other visible screw: adım 3, 3 resimden 2. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove hidden screw and other visible screw: adım 3, 3 resimden 3.
    • Peel off the rubber grip on the back by grasping one of the corners and pulling it away from the camera body.

    • Once removed, a hidden screw is revealed.

    • Remove both screws from the rear of the camera.

  4. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove bottom screws: adım 4, 1 resimden 1.
    • Remove the two indicated screws from the bottom of the camera.

  5. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Lift and remove the rear panel: adım 5, 3 resimden 1. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Lift and remove the rear panel: adım 5, 3 resimden 2. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Lift and remove the rear panel: adım 5, 3 resimden 3.
    • When lifting the panel, make sure not to lift it too high, since you'll run the risk of tearing the cable, or damaging the connector on the board.

    • Flip the lock on the flex cable connector up with a spudger.

    • The front panel should pop off, now that the cable has been disconnected.

    • When reassembling the device, make sure to insert the left side of the front panel first, since it has a small lip that needs to fit under the left part of the camera case.

  6. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Disconnect all the labeled cables: adım 6, 3 resimden 1. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Disconnect all the labeled cables: adım 6, 3 resimden 2. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Disconnect all the labeled cables: adım 6, 3 resimden 3.
    • Disconnect all the indicated connectors by opening their latches.

    • Remove the flex cable that connects the logic board to the secondary control board.

    • Pull the small green connector out of its socket. Be careful when removing it, as it is possible to tear the tiny wires running into the connector.

    • Disconnect the two hidden connectors under the top connector indicated in pink.

    • Disconnect the third hidden connector.

  7. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove the secondary control board: adım 7, 2 resimden 1. Canon EOS 20D Secondary Control Board (C-Board 010) Replacement, Remove the secondary control board: adım 7, 2 resimden 2.
    • Remove the three screws from the edges of the board.

    • Flip the board up and out so that the ground connection can be unscrewed.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Alec M

Üyelik tarihi: 08-05-2016

1.225 İtibar

5 adet Kılavuz yazıldı

0 Comments

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 2

Son 30 gün: 18

Her zaman: 823