Giriş

Use this guide to replace or repair your speaker.

Parçalar

Hiçbir parçaya gerek yok.

Orient the camera so that the viewfinder is on your left and the lens is on your right.
  • Orient the camera so that the viewfinder is on your left and the lens is on your right.

  • Remove the 4mm #00 Phillips screw.

Yorum Ekle

Reorient the camera with the back button pad and viewfinder towards you.
  • Reorient the camera with the back button pad and viewfinder towards you.

  • Remove the three 4mm #00 Phillips screws shown on the rear face of camcorder.

Yorum Ekle

Remove the plastic cover from the rear of the camcorder by gently pulling it towards you while holding the camera as shown. The Battery Should be removed at this point, please ignore it in the picture.
  • Remove the plastic cover from the rear of the camcorder by gently pulling it towards you while holding the camera as shown.

  • The Battery Should be removed at this point, please ignore it in the picture.

Yorum Ekle

Remove the 4mm #00 Phillips screw located to the right of the LCD release switch.
  • Remove the 4mm #00 Phillips screw located to the right of the LCD release switch.

Yorum Ekle

Open the LCD by using the release switch.
  • Open the LCD by using the release switch.

  • Reorient the camera with the playback button pad and edge of LCD screen facing you.

  • Remove the 4mm #00 Phillips screw shown.

Yorum Ekle

Reorient the camera with the top facing you.  The side with the LCD screen should be on the right and the other side panel should be on the right.
  • Reorient the camera with the top facing you. The side with the LCD screen should be on the right and the other side panel should be on the right.

  • Open the pop up flash on the top of the camcorder.

  • A loud clicking noise is expected.

  • Remove the 4mm #00 Phillips screw shown.

Yorum Ekle

Reorient the camera with the bottom facing you, LCD screen on the right, side panel on the left. Open the tape deck by sliding the switch and moving the deck cover to the left as shown.
  • Reorient the camera with the bottom facing you, LCD screen on the right, side panel on the left.

  • Open the tape deck by sliding the switch and moving the deck cover to the left as shown.

Yorum Ekle

Remove 4mm #00 Phillips screw.
  • Remove 4mm #00 Phillips screw.

Yorum Ekle

Reorient camera with lens facing  you.
  • Reorient camera with lens facing you.

  • Remove the #00 Philips 4mm screw shown on the hinge of the tape deck cover.

Yorum Ekle

To remove the camcorder lens hood, twist the hood to counterclockwise and it will come loose, then pull towards you. To remove the camcorder lens hood, twist the hood to counterclockwise and it will come loose, then pull towards you.
  • To remove the camcorder lens hood, twist the hood to counterclockwise and it will come loose, then pull towards you.

Yorum Ekle

Close the tape deck by gently pushing it toward the body of the camera. Slide and remove the plastic cover on the bottom right, exposing the interface shown.
  • Close the tape deck by gently pushing it toward the body of the camera.

  • Slide and remove the plastic cover on the bottom right, exposing the interface shown.

Yorum Ekle

Gently pull the front plastic cover towards you to remove. Gently pull the front plastic cover towards you to remove.
  • Gently pull the front plastic cover towards you to remove.

Yorum Ekle

Remove 2 Philips #00 4mm screw shown.
  • Remove 2 Philips #00 4mm screw shown.

Yorum Ekle

Reorient the camera so you are looking at the side of the camera with the viewfinder on the left and lens on the right.
  • Reorient the camera so you are looking at the side of the camera with the viewfinder on the left and lens on the right.

  • Holding the camera as shown,remove the 4mm #00 Phillips screw.

Yorum Ekle

Remove the 4 Philips #00 4mm screws shown.
  • Remove the 4 Philips #00 4mm screws shown.

Yorum Ekle

Reorient the camera with the lens facing you.
  • Reorient the camera with the lens facing you.

  • Gently pull the side panel of the camera to the right to remove.

  • Be aware that that there are wires connecting the cover to the body of the device, so the side cover will not come off entirely.

Yorum Ekle

The side of the device should now be open as shown.  Again, there are wire connections between the side cover and the body of the camcorder. Do not separate the two entirely!
  • The side of the device should now be open as shown. Again, there are wire connections between the side cover and the body of the camcorder. Do not separate the two entirely!

Yorum Ekle

Remove the screw above the speaker's housing.
  • Remove the screw above the speaker's housing.

Yorum Ekle

Remove the small battery with the "Caution" on it.
  • Remove the small battery with the "Caution" on it.

Yorum Ekle

Remove the screw from inside the battery housing.
  • Remove the screw from inside the battery housing.

Yorum Ekle

Remove the 3 screws holding the metal piece over the speaker.
  • Remove the 3 screws holding the metal piece over the speaker.

Yorum Ekle

Lift up and remove the metal cover.
  • Lift up and remove the metal cover.

Yorum Ekle

Lift and remove the speaker.
  • Lift and remove the speaker.

Yorum Ekle

Replace the broken speaker with a new one.
  • Replace the broken speaker with a new one.

  • The speaker's wires need to be desoldered.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Jeanette Neethling

Üyelik tarihi: 19-01-2011

531 İtibar

5 adet Kılavuz yazıldı

Takım

Cal Poly, Team 1-12, Amido Winter 2011 Cal Poly, Team 1-12, Amido Winter 2011 üyesi

CPSU-AMIDO-W11S1G12

4 Üyeler

6 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 4

Her zaman: 588