Tehlike
Tehlikeli Olma Potansiyeli Var
Bu talimat doğru şekilde uygulanmazsa yaralanma meydana gelebilir. Dikkatli olun ve tüm uyarıları takip edin.
Tehlike

Giriş

This guide will instruct you how to remove the front and back covers from the camera and disassemble the flash in order to replace or repair it.

Parçalar

Hiçbir parçaya gerek yok.

The battery hatch is on the bottom of the camera.
    • The battery hatch is on the bottom of the camera.

    • CAUTION: Locate the switch to open the hatch and push gently toward the front of the camera. Too much force can break the hatch.

    • While the switch is pushed forward, pull the cover away from the camera.

Can the hatch be replaced. The piece that holds the hatch is broken.

alisonbforman46 - Yanıt

This camera requires AA batteries. To remove batteries, simply allow them to fall out of the camera.
    • This camera requires AA batteries. To remove batteries, simply allow them to fall out of the camera.

    • The clock battery cover is shown here in the purple circle. Use a fingernail to lift the battery out of the camera.

Yorum Ekle

  • When replacing the AA batteries, verify they are oriented correctly by following the (+) and (-) signs on the camera.

Yorum Ekle

  • Remove the screw located under the rubber flap on the left side of the camera using a magnetic screwdriver.

Yorum Ekle

  • Remove the two screws located on the other side of the camera using a magnetic screwdriver

Yorum Ekle

  • Remove the three screws located at the bottom of the camera using a magnetic screwdriver.

Yorum Ekle

  • Open the battery cover.

  • Using the iPod tool, push up gently around all edges of the camera.

Yorum Ekle

  • Press and hold down the button shown in the blue circle.

  • While pressing the button, rotate the lens cover in a counter-clockwise direction to remove it.

Yorum Ekle

  • Remove the front cover of the camera.

    • This may require a bit of force.

Yorum Ekle

  • Remove the one (1) screw from the top of the camera, on the left side of the flash (looking from the front) using a Phillips #00 screwdriver.

  • Lift the black plastic covering off the circuit board.

Yorum Ekle

  • Remove the green circuit board from the top. Looking from the front of the camera, first lift the left side up above the black peg. The board should then slide out to the left.

  • The clear flash lens may fall out. Do not worry this will not affect the camera and can easily be placed back in its spot.

Yorum Ekle

  • Unsolder the cables under the circuit board.

Yorum Ekle

  • The flash logic board can now be removed from the camera and replaced.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

3 başka kişi bu kılavuzu tamamladı.

Zach

Üyelik tarihi: 11-10-2010

230 İtibar

6 adet Kılavuz yazıldı

Takım

Cal Poly, Team 9-19, Regan Fall 2010 Cal Poly, Team 9-19, Regan Fall 2010 üyesi

CPSU-REGAN-F10S9G19

4 Üyeler

7 adet Kılavuz yazıldı

Bir Yorum

Zach, can you show how to replace the Ring Release Button? The release button appears to be fixed to the front cover once it is removed. Can we purchase a replacement release button?

Jae Ennis - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 3

Son 30 Gün: 19

Her zaman: 14,827