Eşyalarını Tamir Et Topluluk Mağaza

Canon PowerShot SD1200 IS Motherboard

Giriş

Use this guide to access the motherboard to reseat connections on the motherboard or to remove the motherboard for replacement.

Neye ihtiyacın var

  1. Canon PowerShot SD1200 IS Motherboard, Front and Rear Covers: adım 1, 1 resimden 1.

    • Remove the battery.

    Düzenle

  2. Canon PowerShot SD1200 IS Motherboard: adım 2, 3 resimden 1. Canon PowerShot SD1200 IS Motherboard: adım 2, 3 resimden 2. Canon PowerShot SD1200 IS Motherboard: adım 2, 3 resimden 3.

    • Remove the two screws from the side of the camera casing with the strap. (4mm Phillips 00)

    • Remove the two screws from the bottom of the camera. (4mm Phillips 00)

    • Remove the two screws from the right side of the camera opposite the strap. (2mm Phillips 00)

    Düzenle

  3. Canon PowerShot SD1200 IS Motherboard: adım 3, 2 resimden 1. Canon PowerShot SD1200 IS Motherboard: adım 3, 2 resimden 2.

    • Pull off the front cover.

    • If the top of the cover sticks, use gentle downward pressure on the retention clips above the lens to release.

    • Remove the back cover.

    Düzenle

  5. Canon PowerShot SD1200 IS Motherboard, Motherboard: adım 4, 1 resimden 1.

    • Remove the microphone connector by gripping it with the tool and gently, with a wiggling motion, pull it out.

    • Pull the connector straight out by the white connector. Pulling on the wires will damage them.

    Düzenle

  6. Canon PowerShot SD1200 IS Motherboard: adım 5, 1 resimden 1.

    • Lift off the mechanical shutter button assembly.

    Düzenle

  7. Canon PowerShot SD1200 IS Motherboard: adım 6, 2 resimden 1. Canon PowerShot SD1200 IS Motherboard: adım 6, 2 resimden 2.

    • Use the spudger to lift the tab on the Zero Insertion Force (ZIF) connector located at the bottom of the motherboard.

    • Be sure you are prying up on the hinged retaining flap, not the connector itself.

    • Slide out the ribbon cable.

    • Use the spudger to pry up each side of the Flat-Topped Connectors

    Düzenle

  8. Canon PowerShot SD1200 IS Motherboard: adım 7, 1 resimden 1.

    • Remove the press fit ribbon cable by prying upward with spudger tool.

    • It is not necessary to remove the Lens or Flash Assemblies to remove the motherboard.

    Düzenle

  9. Canon PowerShot SD1200 IS Motherboard: adım 8, 1 resimden 1.

    • Remove the bottom right screw from the motherboard. (4mm Phillips 00)

    • Remove top and lower left black screws from the motherboard. (2.5mm Phillips 00)

    Düzenle

  10. Canon PowerShot SD1200 IS Motherboard: adım 9, 1 resimden 1.

    • Lift out the motherboard.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Jeff Casper

Üyelik tarihi: 09/15/16

848 İtibar

7 adet Kılavuz yazıldı

Rozetler: 18

+15 tane daha rozet

Ekip

USF Tampa, Team 17-5, Blackwell Fall 2016 USF Tampa, Team 17-5, Blackwell Fall 2016 üyesi

USFT-BLACKWELL-F16S17G5

3 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 4

Son 30 gün: 11

Her zaman: 404