Skip to main content

Giriş

The motherboard can be damaged because of overheat and a short circuit which can cause the camera to stop working. This guide will show how to replace the motherboard in the device.

  1. Remove two 2mm Phillips #00 screws on both sides of the camera. Remove two 2mm Phillips #00 screws on both sides of the camera. Remove two 2mm Phillips #00 screws on both sides of the camera.
    • Remove two 2mm Phillips #00 screws on both sides of the camera.

  2. Remove the 4mm Phillips #000 screw from the bottom.
    • Remove the 4mm Phillips #000 screw from the bottom.

  3. Remove the front face panel of the camera.
    • Remove the front face panel of the camera.

  4. Remove the rear panel of the camera by using hand with firm pressure.
    • Remove the rear panel of the camera by using hand with firm pressure.

    • The user interface panel, side and bottom panel of the camera may fall down by itself while you are taking the rear panel of the camera.

  5. Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın

    Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın
  6. Remove the 3mm Phillips #000 screw from the top of the camera.
    • Remove the 3mm Phillips #000 screw from the top of the camera.

  7. Pry the three golden ribbons off the motherboard using a plastic opening tool. Pry the three golden ribbons off the motherboard using a plastic opening tool. Pry the three golden ribbons off the motherboard using a plastic opening tool.
    • Pry the three golden ribbons off the motherboard using a plastic opening tool.

  8. Use a plastic opening tool to flip up the retaining flap on the  ribbon cable ZIF socket. Once released, the small black tab will point straight away from the front face of the camera and the golden film will no longer be attached to the motherboard. Once released, the small black tab will point straight away from the front face of the camera and the golden film will no longer be attached to the motherboard.
    • Use a plastic opening tool to flip up the retaining flap on the ribbon cable ZIF socket.

    • Once released, the small black tab will point straight away from the front face of the camera and the golden film will no longer be attached to the motherboard.

  9. Unplug the small chip from the face of the camera using a pair of tweezers. Unplug the small chip from the face of the camera using a pair of tweezers.
    • Unplug the small chip from the face of the camera using a pair of tweezers.

  10. Remove the three 3mm Phillips #000 screws from the motherboard. Remove the three 3mm Phillips #000 screws from the motherboard. Remove the three 3mm Phillips #000 screws from the motherboard.
    • Remove the three 3mm Phillips #000 screws from the motherboard.

  11. Remove the 3mm Phillips #000 screw from the rear face of the camera.
    • Remove the 3mm Phillips #000 screw from the rear face of the camera.

  12. Remove the top panel from the camera.
    • Remove the top panel from the camera.

  13. Remove the motherboard. Remove the motherboard.
    • Remove the motherboard.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Faris Rezwan

Üyelik tarihi: 21-05-2018

433 Reputation

2 adet Kılavuz yazıldı

Team

IUPUI, Team S1-G2, Harley Spring 2018 IUPUI, Team S1-G2, Harley Spring 2018 üyesi

IUPUI-HARLEY-S18S1G2

7 Üyeler

4 adet Kılavuz yazıldı

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 5

All Time: 157