Eşyalarını Tamir Et Topluluk Mağaza

Canon PowerShot SD700 Backlight Replacement

Giriş

Follow these instructions to remove and install a new backlight.

Neye ihtiyacın var

  1. Canon PowerShot SD700 Backlight Replacement, Outside Case: adım 1, 1 resimden 1.

    • Turn off the camera by pressing the power button above the LCD screen.

    Düzenle

  2. Canon PowerShot SD700 Backlight Replacement: adım 2, 1 resimden 1.

    • Remove the two small screws on the bottom of the camera using a Phillips #00 screwdriver.

    Düzenle

  3. Canon PowerShot SD700 Backlight Replacement: adım 3, 1 resimden 1.

    • Use a Phillips #00 screwdriver to remove the two small screws on the right side of the camera.

    Düzenle

  4. Canon PowerShot SD700 Backlight Replacement: adım 4, 1 resimden 1.

    • Use a Phillips #00 screwdriver to remove the screw on the left of the camera under the A/V out digital label.

    Düzenle

  6. Canon PowerShot SD700 Backlight Replacement: adım 5, 1 resimden 1.

    • Use a Phillips #00 screwdriver to remove the screw on the bottom of the camera near the battery and memory card slots.

    • This screw will be longer than the rest of the screws.

    Düzenle

  7. Canon PowerShot SD700 Backlight Replacement: adım 6, 1 resimden 1.

    • Remove the front, back, and side casings from the camera and set to the side.

    Düzenle

  8. Canon PowerShot SD700 Backlight Replacement, LCD screen: adım 7, 1 resimden 1.

    • Remove the two screws that connect the LCD and backlight to the main body of the camera.

    Düzenle

  9. Canon PowerShot SD700 Backlight Replacement: adım 8, 3 resimden 1. Canon PowerShot SD700 Backlight Replacement: adım 8, 3 resimden 2. Canon PowerShot SD700 Backlight Replacement: adım 8, 3 resimden 3.

    • Gently pry the LCD and the backlight from the main body of the camera.

    • Gently pry the LCD from the backlight.

    • The thin ribbon cable is for the backlight.

    • The thick ribbon cable is for the LCD screen.

    Düzenle

  10. Canon PowerShot SD700 Backlight Replacement: adım 9, 1 resimden 1.

    • Carefully lift the ZIF connector that covers the thick ribbon cable.

    • This ZIF connector is fragile. Use caution when lifting it from its down position.

    • Insert the new LCD and reassemble the camera.

    Düzenle

  11. Canon PowerShot SD700 Backlight Replacement, Backlight: adım 10, 1 resimden 1.
    Bu adımda kullanılan alet:
    Tweezers
    $4.99
    Satın Al

    • Unplug the ribbon from the housing on the circuitry.

    • Take the new ribbon and insert it into the housing.

    • Tweezers or a tool with a sharp point can be used.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

4 tane daha katılımcı ile

Emilio Rossi

Üyelik tarihi: 04/07/11

113 İtibar

3 adet Kılavuz yazıldı

Rozetler: 8

+5 tane daha rozet

Ekip

Cal Poly, Team 9-71, Walters Spring 2011 Cal Poly, Team 9-71, Walters Spring 2011 üyesi

CPSU-WALTERS-S11S9G71

4 Üyeler

9 adet Kılavuz yazıldı

0Kılavuz Yorumları

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 3

Son 7 gün: 10

Son 30 gün: 18

Her zaman: 1,669