Eşyalarını Tamir Et Topluluk Mağaza

Canon Powershot ELPH 100 HS Outer Case Replacement

Giriş

Hello everyone, this step by step guide will hep you put a new outer case replacement on your Canon Powershot ELPH 100 HS!

Neye ihtiyacın var

  1. Canon Powershot ELPH 100 HS Outer Case Replacement, Outer Case: adım 1, 1 resimden 1.

    • Using the Phillips #00 screwdriver, remove the two 3.1mm screws from the bottom of the camera.

    • Keep track of all the screws that are being taken out from the outer case.

    • The display screen of the camera should be facing towards you.

    Düzenle

  2. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 2, 1 resimden 1.

    • Ensure that the screen is facing you, and then rotate it till you see the screws on the side of the camera.

    • Use the Phillips #00 screwdriver to remove the two 3.1 mm screws.

    Düzenle

  3. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 3, 2 resimden 1. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 3, 2 resimden 2.

    • With the screen still facing you, rotate the camera 180 degrees.

    • The side with the charging port should now be facing up.

    Düzenle

  5. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 4, 2 resimden 1. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 4, 2 resimden 2.

    • Use the Philips #00 screwdriver to pry open the charging port cover.

    • Once you pry open the charging port cover, rotate the cover so that you have access to the screw underneath. Which is seen in the next image.

    • Remove both 3.1 mm screws using the Phillips #00 screwdriver.

    • The image still shows the screw from step 3 in place.

    Düzenle

  6. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 5, 2 resimden 1. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 5, 2 resimden 2.

    • Turn the camera so the bottom is once again facing up.

    • With the battery door still open, use a spudger to remove the cover from the front of the camera.

    • Carefully go around all of the edges until the cover is released.

    Düzenle

  7. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 6, 1 resimden 1.

    • Once the entire front cover has been released carefully pull it off.

    • Be careful not to break the tabs that hold it in place.

    Düzenle

  8. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 7, 3 resimden 1. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 7, 3 resimden 2. Canon Powershot ELPH 100 HS Outer Case Replacement: adım 7, 3 resimden 3.

    • Just like Step 4-6 , carefully use the Spudger to remove the back cover.

    • Go along all the borders of the back cover so that it releases from the camera safely.

    • Be careful not to break the tabs.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

6 farklı kişi bu kılavuzu tamamladı.

Yazar

8 tane daha katılımcı ile

Jacob

Üyelik tarihi: 03/17/15

570 İtibar

3 adet Kılavuz yazıldı

Rozetler: 10

+7 tane daha rozet

Ekip

Michigan Tech, Team 1-10, Lauer Spring 2015 Michigan Tech, Team 1-10, Lauer Spring 2015 üyesi

MTU-LAUER-S15S1G10

2 Üyeler

5 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 4

Son 30 gün: 18

Her zaman: 1,586