Giriş

If the LCD screen has cracked, stopped working, or malfunctioned in any other way, you will need to replace the screen. This guide will break down the camera all the way to having a separate LCD screen from the camera. Follow the guide in reverse in order to install the new LCD screen.

Parçalar

Hiçbir parçaya gerek yok.

Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop. Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop. Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop.
  • Remove the strap from the camera by pulling the thin cord out, creating a small loop, then pushing the thicker cord back through this loop.

Yorum Ekle

Remove the two phillips screws (2.83 mm) from the left side panel of the camera casing. The left panel can now be removed. However, one piece of tape attaches it to the camera, so a spudger may be required to ease the panels off. Repeat for the right side panel of the camera.
  • Remove the two phillips screws (2.83 mm) from the left side panel of the camera casing.

  • The left panel can now be removed. However, one piece of tape attaches it to the camera, so a spudger may be required to ease the panels off.

  • Repeat for the right side panel of the camera.

  • Keep track of which screws go where. There are a couple sets of screws to take out and they are all small and look the same.

Yorum Ekle

Remove the 6 phillips screws (3.69 mm) from the bottom of the camera casing. Remove the 6 phillips screws (3.69 mm) from the bottom of the camera casing. Remove the 6 phillips screws (3.69 mm) from the bottom of the camera casing.
  • Remove the 6 phillips screws (3.69 mm) from the bottom of the camera casing.

Yorum Ekle

Remove the 2 phillips screws (2.79 mm) on the left side of the camera where the metal panel used to be. Repeat for the 2 phillips screws (2.79 mm) right side of the camera. Repeat for the 2 phillips screws (2.79 mm) right side of the camera.
  • Remove the 2 phillips screws (2.79 mm) on the left side of the camera where the metal panel used to be.

  • Repeat for the 2 phillips screws (2.79 mm) right side of the camera.

Yorum Ekle

With the LCD screen facing up towards you, start at the bottom of the camera and gently pull off the back of the casing. With the LCD screen facing up towards you, start at the bottom of the camera and gently pull off the back of the casing.
  • With the LCD screen facing up towards you, start at the bottom of the camera and gently pull off the back of the casing.

Yorum Ekle

With the front side (with the lens) facing up towards you, start at the bottom of the camera and gently pull off the front of the casing. The nob that previously held the camera strap will no longer be attached to the camera once you remove the camera casing. When putting the camera back together, remember to put the nob back into position before replacing the casing. The nob that previously held the camera strap will no longer be attached to the camera once you remove the camera casing. When putting the camera back together, remember to put the nob back into position before replacing the casing.
  • With the front side (with the lens) facing up towards you, start at the bottom of the camera and gently pull off the front of the casing.

  • The nob that previously held the camera strap will no longer be attached to the camera once you remove the camera casing. When putting the camera back together, remember to put the nob back into position before replacing the casing.

Yorum Ekle

Slide the labeled piece toward the LCD screen and release. The tab will spring open.
  • Slide the labeled piece toward the LCD screen and release.

  • The tab will spring open.

Yorum Ekle

Look at the bottom of the camera. Take out the phillips screw (1.77 mm) holding on the bottom plastic piece. The bottom plastic piece is held on to the main frame of the camera only by two thin wires.
  • Look at the bottom of the camera. Take out the phillips screw (1.77 mm) holding on the bottom plastic piece.

  • The bottom plastic piece is held on to the main frame of the camera only by two thin wires.

Yorum Ekle

Orient the camera with the lens facing up and the flash towards you for the clearest visibility. Using a pair of tweezers, gently move the red and black wires away from the lens.
  • Orient the camera with the lens facing up and the flash towards you for the clearest visibility.

  • Using a pair of tweezers, gently move the red and black wires away from the lens.

Yorum Ekle

Using tweezers or your finger nails, pull up the brown flaps where the three orange film strips meet the circuit board. Use the tweezers to pull all three orange film strips out of each port. The strips should come out easily. Use the tweezers to pull all three orange film strips out of each port. The strips should come out easily.
  • Using tweezers or your finger nails, pull up the brown flaps where the three orange film strips meet the circuit board.

  • Use the tweezers to pull all three orange film strips out of each port. The strips should come out easily.

Yorum Ekle

Flip the camera over to the side with the LCD screen. Gently remove the plastic cover that borders the LCD screen starting with the top left corner, then the bottom left corner, and finally the bottom and top right corners. The LCD screen is now loose from the camera; it should only be connected by a gold strip that attaches to the circuit board.
  • Flip the camera over to the side with the LCD screen.

  • Gently remove the plastic cover that borders the LCD screen starting with the top left corner, then the bottom left corner, and finally the bottom and top right corners.

  • The LCD screen is now loose from the camera; it should only be connected by a gold strip that attaches to the circuit board.

Yorum Ekle

Turn the camera back to the front side, with the lens facing up and the LCD facing down.
  • Turn the camera back to the front side, with the lens facing up and the LCD facing down.

  • Remove the phillips screw (3.30 mm) located below the flash on the circuit board.

Yorum Ekle

At this point, the LCD screen and the circuit board are only attached to the camera by a thin gold strip on the far left of the circuit board. Slide the gold strip that connects the LCD screen to the circuit board through the small gap at the bottom of the camera. Slide the gold strip that connects the LCD screen to the circuit board through the small gap at the bottom of the camera.
  • At this point, the LCD screen and the circuit board are only attached to the camera by a thin gold strip on the far left of the circuit board.

  • Slide the gold strip that connects the LCD screen to the circuit board through the small gap at the bottom of the camera.

Yorum Ekle

Using a soldering station and solder wick or other solder removing instrument, remove the solder holding the two wires of the LCD screen to the circuit board. You have now completely removed your LCD screen. It can now be replaced or cleaned.
  • Using a soldering station and solder wick or other solder removing instrument, remove the solder holding the two wires of the LCD screen to the circuit board.

  • You have now completely removed your LCD screen. It can now be replaced or cleaned.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Paul Fallon

Üyelik tarihi: 10-04-2012

114 İtibar

6 adet Kılavuz yazıldı

Takım

Cal Poly, Team 17-28, Amido Spring 2012 Cal Poly, Team 17-28, Amido Spring 2012 üyesi

CPSU-AMIDO-S12S17G28

4 Üyeler

9 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 1

Son 30 Gün: 12

Her zaman: 1,169