Parçalar

Hiçbir parçaya gerek yok.

Remove the four screws on the side of the speaker.
  • Remove the four screws on the side of the speaker.

Yorum Ekle

Remove the two back screws on the bottom of the camera.
  • Remove the two back screws on the bottom of the camera.

  • Note: Bottom screws are longer than the top ones, so label accordingly for easy reassembly.

Yorum Ekle

Remove the four screws on the side opposite of the speaker.
  • Remove the four screws on the side opposite of the speaker.

Yorum Ekle

Once all screws have been removed, gently pry open bottom casing. With tweezers, carefully remove ribbon from LCD screen.
  • Once all screws have been removed, gently pry open bottom casing.

  • With tweezers, carefully remove ribbon from LCD screen.

  • Set bottom casing aside.

Yorum Ekle

Gently pry apart the top casing using tweezers. Set the top casing aside. Set the top casing aside.
  • Gently pry apart the top casing using tweezers.

  • Set the top casing aside.

Yorum Ekle

Mac RAM Kitleri
Mac'inizi hızlandırın. Hafızasını en yükseğe çıkar.
Mac RAM Kitleri
Mac'inize daha fazla bellek alın.
Use tweezers or prongs to pry the LCD screen off from the opening. Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.
  • Use tweezers or prongs to pry the LCD screen off from the opening.

  • Note: The bottom of the LCD screen is attached to the frame by a few pieces of black tape.

Yorum Ekle

Lift up the LCD screen, slowly move it to the other side. Lift up the LCD screen, slowly move it to the other side.
  • Lift up the LCD screen, slowly move it to the other side.

Yorum Ekle

Pry off the LCD casing. Pry off the LCD casing.
  • Pry off the LCD casing.

Yorum Ekle

Flip open the connector holding the ribbon. Pull out the LCD screen with the ribbon from the camera. Pull out the LCD screen with the ribbon from the camera.
  • Flip open the connector holding the ribbon.

  • Pull out the LCD screen with the ribbon from the camera.

Yorum Ekle

Remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off.
  • Remove two screws on the side where the battery is located.

  • Remove the lanyard loop after the screws come off.

  • Slowly pull the side casing so it becomes dislocated from the top of the camera frame.

Yorum Ekle

On the front of the camera near the flash flip the connector holding the ribbon. Remove the ribbon from the connector.
  • On the front of the camera near the flash flip the connector holding the ribbon.

  • Remove the ribbon from the connector.

Yorum Ekle

Carefully remove the L shaped frame from the camera. At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab. Pop the frame off the bumps and tabs.
  • Carefully remove the L shaped frame from the camera.

  • At the bottom of the camera the L shaped frame is being held in by two plastic bumps and a metal tab.

  • Pop the frame off the bumps and tabs.

  • Note: There is a yellow and orange wire soldered onto the camera. Be careful not to pull them off.

Yorum Ekle

This is the flash assembly. It needs to be removed with soldering points circled.
  • This is the flash assembly.

  • It needs to be removed with soldering points circled.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Christian

Üyelik tarihi: 28-01-2011

320 İtibar

3 adet Kılavuz yazıldı

Takım

Cal Poly, Team 4-38, Regan Winter 2011 Cal Poly, Team 4-38, Regan Winter 2011 üyesi

CPSU-REGAN-W11S4G38

4 Üyeler

7 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 3

Her zaman: 2,441