Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Giriş

If your Casio Exilim EX-Z850 is no longer working correctly, you most likely need to replace the motherboard.

The motherboard is responsible for keeping your device functioning properly. It connects all of the principle components of the camera. If the motherboard is not working correctly, everything has the possibility of not working right. If your device continues to malfunction, you should replace the motherboard.

Make sure to power down your camera before you begin.

  1. Using the Phillips #00 screwdriver, remove the four screws from the side of the speaker.
    • Using the Phillips #00 screwdriver, remove the four screws from the side of the speaker.

  2. Using the Phillips #00 screwdriver, remove the four long screws from the bottom of the camera.
    • Using the Phillips #00 screwdriver, remove the four long screws from the bottom of the camera.

    • When reassembling the camera, the longer screws go on the bottom of the camera.

  3. Using the Phillips #00 screwdriver, remove the four screws from the side opposite of the speaker.
    • Using the Phillips #00 screwdriver, remove the four screws from the side opposite of the speaker.

  4. Pry open bottom casing gently after all screws have been removed. With tweezers, carefully remove the ribbon from the LCD screen. Set the bottom casing aside.
    • Pry open bottom casing gently after all screws have been removed.

    • With tweezers, carefully remove the ribbon from the LCD screen.

    • Set the bottom casing aside.

  5. Pry apart the top casing using tweezers. Set the top casing aside. The bottom left screw on the board is orange and the longest screw.
    • Pry apart the top casing using tweezers.

    • Set the top casing aside.

    • The bottom left screw on the board is orange and the longest screw.

  6. Carefully remove the pieces of black tape on the bottom of the LCD screen that attach it to the frame. Use tweezers to pry the LCD screen off from the opening.
    • Carefully remove the pieces of black tape on the bottom of the LCD screen that attach it to the frame.

    • Use tweezers to pry the LCD screen off from the opening.

  7. Lift  the LCD screen and move it to the other side. Lift  the LCD screen and move it to the other side.
    • Lift the LCD screen and move it to the other side.

  8. Using a pair of tweezers, pry off the LCD casing. Using a pair of tweezers, pry off the LCD casing.
    • Using a pair of tweezers, pry off the LCD casing.

  9. Flip open the connector holding the ribbon. Use the tweezers to carefully pull out the LCD screen with the ribbon from the camera. Use the tweezers to carefully pull out the LCD screen with the ribbon from the camera.
    • Flip open the connector holding the ribbon.

    • Use the tweezers to carefully pull out the LCD screen with the ribbon from the camera.

  10. Using the Phillips #00 screwdriver, remove two screws on the side where the battery is located. Remove the lanyard loop after the screws come off.
    • Using the Phillips #00 screwdriver, remove two screws on the side where the battery is located.

    • Remove the lanyard loop after the screws come off.

    • Pull the side casing so it becomes dislocated from the top of the camera frame.

  11. On the front of the camera near the flash, flip the connector holding the ribbon. Remove the ribbon from the connector.
    • On the front of the camera near the flash, flip the connector holding the ribbon.

    • Remove the ribbon from the connector.

  12. Carefully remove the L-shaped frame from the camera. The L shaped frame is being held in by two plastic bumps and a metal tab at the bottom of the camera. Pop the frame off the bumps and tabs.
    • Carefully remove the L-shaped frame from the camera.

    • The L shaped frame is being held in by two plastic bumps and a metal tab at the bottom of the camera.

    • Pop the frame off the bumps and tabs.

    • Potential for device damage: Be careful not to pull off the yellow and orange wire soldered onto the camera.

  13. Flip the connector and remove the ribbon cable from the motherboard next to the lens. Flip the connector and remove the ribbon cable from the motherboard next to the lens.
    • Flip the connector and remove the ribbon cable from the motherboard next to the lens.

  14. Remove the frame on the back side of the camera where the LCD screen was. Use the Phillips #00 screwdriver to remove the two screws connecting the frame to the camera.
    • Remove the frame on the back side of the camera where the LCD screen was.

    • Use the Phillips #00 screwdriver to remove the two screws connecting the frame to the camera.

    • Slowly pry off the frame from the camera.

    • After removing the frame, a plastic piece with two yellow buttons should fall off.

    • Do not pull the plastic piece off as it is soldered to two wires: a yellow and orange one.

  15. On the back of the camera where the LCD screen was, remove the 3 screws located behind the lens using the Phillips #00 screwdriver.
    • On the back of the camera where the LCD screen was, remove the 3 screws located behind the lens using the Phillips #00 screwdriver.

  16. Remove the large orange ribbon previously held in by screws from the camera.
    • Remove the large orange ribbon previously held in by screws from the camera.

  17. On the backside of the camera where the indicator lamp is located, remove the two screws using the Phillips #00 screwdriver.
    • On the backside of the camera where the indicator lamp is located, remove the two screws using the Phillips #00 screwdriver.

  18. On the front side of the indicator lamp remove the screw using the Phillips #00 screwdriver. On the front side of the indicator lamp remove the screw using the Phillips #00 screwdriver. On the front side of the indicator lamp remove the screw using the Phillips #00 screwdriver.
    • On the front side of the indicator lamp remove the screw using the Phillips #00 screwdriver.

  19. Desolder the lens from the motherboard. Desolder the wire from the motherboard.
    • Desolder the lens from the motherboard.

    • Desolder the wire from the motherboard.

    • The motherboard is now detached from the rest of the camera.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Bir başkası bu kılavuzu tamamladı.

Jennifer Roth

Üyelik tarihi: 28-01-2011

158 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team 4-38, Regan Winter 2011 Cal Poly, Team 4-38, Regan Winter 2011 üyesi

CPSU-REGAN-W11S4G38

4 Üyeler

13 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 6

Her zaman: 3,621