Parçalar

Hiçbir parçaya gerek yok.

  • Hold the phone with the back (camera side) facing you. Slide the battery cover off of the phone.

Yorum Ekle

  • Pull the battery out by lifting the black tab on the left side of the battery.

Yorum Ekle

  • Remove the camera cover of the phone, using your light blue wedge tool.

Yorum Ekle

  • Unscrew the four black Torx head screws, found in each corner of the back.

  • Warning: Unscrewing the screw indicated in the picture will void any warranty on the phone.

Yorum Ekle

  • Unscrew the black Phillips head screw below the right speaker.

Yorum Ekle

  • After removing the screw, pull up on the motherboard to release it from the circuit board (green tab, see Figure 11). This will simply snap out, and does not require too much force.

Yorum Ekle

  • Remove the keyboard by unscrewing the two pairs of silver Torx head screws that run along the sliding tracks.

Yorum Ekle

  • Remove the four silver Phillips head screws from the screened half of the phone.

Yorum Ekle

  • Use the light blue wedge tool to remove the back. The circuit board will slide out of the slot and will stay attached to the remaining front half of the phone.

Yorum Ekle

  • Unscrew the four Phillips head screws that attach the screen to the front case.

Yorum Ekle

  • Remove the circuit board; pull it apart at the orange tab. This will detach the screen from its circuit board.

Yorum Ekle

  • Attach the new screen by aligning the orange tab with the beige rectangle on the circuit. Secure by pushing down on the bronze piece.

Yorum Ekle

  • Place screen back into front cover.

Yorum Ekle

  • Screw the four smallest silver Torx head screws into the circuit board, which will attach it to the front cover.

Yorum Ekle

  • Feed the circuit board through the back piece.

Yorum Ekle

  • Use the four Phillips head silver screws to attach the back piece to the front of the phone.

Yorum Ekle

  • Slide the circuit board through the slot in the keyboard.

Yorum Ekle

  • Attach the keyboard to the sliding tracks using the four silver Torx screws.

Yorum Ekle

  • Attach the motherboard to the circuit board, aligning the two white rectangles until they snap into place. Lay motherboard into place.

Yorum Ekle

  • Secure the motherboard by screwing the small black Phillips head screw into place, located below the right speaker. Note: You may need to remove the right speaker in order to replace this screw.

Yorum Ekle

  • Place the back cover onto the motherboard, clicking it into place.

Yorum Ekle

  • Secure the back cover by screwing the four long, black Torx screws into the four corners of the back cover.

Yorum Ekle

  • Replace the camera cover.

Yorum Ekle

  • Replace battery, keeping the black tab available to grab.

Yorum Ekle

  • Slide the battery cover back into place.

Yorum Ekle

Sonuç

To reassemble your device, follow these instructions in reverse order.

Laura Kimberly Simonds

Üyelik tarihi: 24-09-2012

301 İtibar

3 adet Kılavuz yazıldı

Takım

University of Maine, Team 1-1, Diaz Fall 2012 University of Maine, Team 1-1, Diaz Fall 2012 üyesi

UMAINE-DIAZ-F12S1G1

4 Üyeler

3 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 Gün: 0

Son 30 Gün: 2

Her zaman: 359