Eşyalarını Tamir Et Topluluk Mağaza

Clarke Floor Sander 07014A 2012 Blower Housing Replacement

Giriş

This guide shows how to remove and replace the blower housing for a Clarke Floor Sander 07014A.

Neye ihtiyacın var

  1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement, Dust Bag: adım 1, 2 resimden 1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement, Dust Bag: adım 1, 2 resimden 2.

    • Before you begin, be sure that the sander is unplugged and powered off.

    • Twist and pull the dust bag collar to disconnect it from the elbow pipe.

    • Remove the dust bag.

    Düzenle

  2. Clarke Floor Sander 07014A 2012 Blower Housing Replacement, Blower Housing: adım 2, 2 resimden 1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement, Blower Housing: adım 2, 2 resimden 2.

    • Peel the rubber sleeve down from the elbow pipe to reveal the pipe socket.

    Düzenle

  4. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 3, 3 resimden 1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 3, 3 resimden 2. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 3, 3 resimden 3.

    • Grasp the elbow pipe with your hands and pull up while twisting to disconnect it from the blower housing.

    • Remove the elbow pipe.

    Düzenle

  5. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 4, 3 resimden 1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 4, 3 resimden 2. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 4, 3 resimden 3.

    • Twist and pull to disconnect both suction hoses from the blower housing.

    Düzenle

  6. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 5, 2 resimden 1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 5, 2 resimden 2.

    • Remove the four 22mm long Phillips screws around the side of the blower housing.

    Düzenle

  7. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 6, 2 resimden 1. Clarke Floor Sander 07014A 2012 Blower Housing Replacement: adım 6, 2 resimden 2.

    • Lift the blower housing upwards and slide it off of the blower assembly.

    • Remove the blower housing.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Yazar

Arthur Shi

Üyelik tarihi: 01/03/18

253.295 İtibar

526 adet Kılavuz yazıldı

Rozetler: 47

+44 tane daha rozet

Ekip

iFixit iFixit üyesi

Staff

135 Üyeler

17.166 adet Kılavuz yazıldı

Bir Yorum

Were do you get the sticker?

JEFFREY - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 8

Son 30 gün: 34

Her zaman: 1,466