Ana içeriğe geç

Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement

Neye ihtiyacın var

  1. Dikkatli ol: adımlar 1-4 yapım altında olarak işaretlenen bir kılavuzdan alınmıştır.

    Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Safety precautions: adım 1, 2 resimden 1. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Safety precautions: adım 1, 2 resimden 2.
    • Make sure the engine is off and cool to the touch before you proceed.

  2. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 2, 1 resimden 1.
    • Place wheel chocks against the roller and rear wheel to prevent the machine from moving.

  3. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 3, 2 resimden 1. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 3, 2 resimden 2.
    • Flip the gas shutoff switch next to the motor to the left into the off position.

  4. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 4, 2 resimden 1. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 4, 2 resimden 2.
    • Grab the plastic housing at the end of the spark plug wire.

    • Pull firmly to disconnect the wire from the spark plug.

  5. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement, Remove the eccentric arms: adım 5, 1 resimden 1.
    • Use a 3/4 inch socket to remove the two bolts on the eccentric arm.

    • You may need to use a 3/4 inch wrench in combination with the socket wrench to hold the nuts in place.

    • During reassembly, apply threadlocker to the bolt securing the eccentric arm to the blade arm.

  6. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 6, 2 resimden 1. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 6, 2 resimden 2.
    • Remove the plastic washer from between the eccentric arm and the blade arm.

  7. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 7, 1 resimden 1.
    • Lift the eccentric arm away from the blade arm.

  8. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 8, 2 resimden 1. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 8, 2 resimden 2.
    • Remove the steel washer from the eccentric shaft.

  9. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 9, 1 resimden 1.
    • Remove the plastic washer from the eccentric shaft.

  10. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 10, 2 resimden 1. Classen Sod Cutter HSC18AHD 2018 Eccentric Arm Replacement: adım 10, 2 resimden 2.
    • Remove the eccentric arm and plastic washer from the eccentric shaft.

    • Repeat steps 5–10 for the other eccentric arm.

    • During reassembly, use a grease gun to add grease to the bearings through the two Zerk fittings on each eccentric arm.

Sonuç

To reassemble your device, follow these instructions in reverse order.

2 farklı kişi bu kılavuzu tamamladı.

Sam Omiotek

Üyelik tarihi: 02/25/19

71.951 İtibar

288 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 6

Son 30 gün: 57

Her zaman: 1,412