Ana içeriğe geç

Giriş

The hard drive may need to be replaced for numinous reasons; a larger capacity drive is needed, a new drive is desired or the old drive is faulty. This guide details how to replace the hard drive. Note that this machine supports 2.5" SATA Hard drives of

  1. Using a Philips Head #1 Screw Driver remove the nine .7mm screws holding the back cover in place. The cover is held on with small plastic tabs. Starting from the back of the machine use your hands to gently prey the back cover from the machine and release these tabs. While a tool is not necessary a plastic plunger can be used to lift the first few tabs.
    • Using a Philips Head #1 Screw Driver remove the nine .7mm screws holding the back cover in place.

    • The cover is held on with small plastic tabs. Starting from the back of the machine use your hands to gently prey the back cover from the machine and release these tabs. While a tool is not necessary a plastic plunger can be used to lift the first few tabs.

  2. Using the tab on the cables connector with your hand unplug the Hard Drive connection cable and remove it from the cable track on the battery.
    • Using the tab on the cables connector with your hand unplug the Hard Drive connection cable and remove it from the cable track on the battery.

  3. Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın

    Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın
  4. Pull back the sticker covering the first screw on the hard drive chaises. Useing a Philips Head #0 screwdriver remove the three screws holding the drive in place. Useing a Philips Head #0 screwdriver remove the three screws holding the drive in place.
    • Pull back the sticker covering the first screw on the hard drive chaises.

    • Useing a Philips Head #0 screwdriver remove the three screws holding the drive in place.

  5. Lift the hard drive from the left side as depicted and remove.
    • Lift the hard drive from the left side as depicted and remove.

  6. Unplug the adapter cable from the drive. No tool is required for this step.
    • Unplug the adapter cable from the drive. No tool is required for this step.

  7. Using a Philips Head #1 Screwdriver remove the four screws holding the hard drive to the chassis. Remove the drive from the chassis. Care that the drive does not fall out once all the screwshave been removed. Remove the drive from the chassis. Care that the drive does not fall out once all the screwshave been removed.
    • Using a Philips Head #1 Screwdriver remove the four screws holding the hard drive to the chassis.

    • Remove the drive from the chassis. Care that the drive does not fall out once all the screwshave been removed.

Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

William Brum

Üyelik tarihi: 04-03-2016

728 İtibar

5 adet Kılavuz yazıldı

Takım

UMass Dartmouth, Team 3-1, Bhusal Spring 2016 UMass Dartmouth, Team 3-1, Bhusal Spring 2016 üyesi

UMASSD-BHUSAL-S16S3G1

3 Üyeler

8 adet Kılavuz yazıldı

Bir Yorum

I am a visual learner and with this guide, I had my hard drive changed and the backplate back on in less than 10 minutes. Thanks for the great guide.

Chris Hartfield - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Past 24 Hours: 0

Past 7 Days: 10

Past 30 Days: 49

Her zaman: 3,878