Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Arşivlendi
Arşivlenmiş Kılavuz
Bu kılavuz sadece arşivsel amaçlarla muhafaza edilmiştir. Onarımınızı gerçekleştirmek için kılavuzun güncel halini kullanın.
Arşivlendi

Giriş

Use this guide to replace the track pad in the Dell XPS 13.

  1. Remove the eight 4 mm T5 Torx screws from the bottom cover. Remove the eight 4 mm T5 Torx screws from the bottom cover.
    • Remove the eight 4 mm T5 Torx screws from the bottom cover.

  2. Use a plastic opening tool to pry open the 'XPS' flap in the middle. Use a plastic opening tool to pry open the 'XPS' flap in the middle.
    • Use a plastic opening tool to pry open the 'XPS' flap in the middle.

  3. Remove the single Phillips screw hidden beneath the flap.
    • Remove the single Phillips screw hidden beneath the flap.

  4. Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.
    • Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.

  5. Remove the bottom cover.
    • Remove the bottom cover.

  6. Pull the battery cable connector towards the battery to disconnect it from its socket. If the connector is stubborn, push a little at one side, then the other, to "walk" it out of its socket.
    • Pull the battery cable connector towards the battery to disconnect it from its socket.

    • If the connector is stubborn, push a little at one side, then the other, to "walk" it out of its socket.

    • If you have trouble walking the connector out of the socket, use the point of a spudger to gently push on the connector indent to slide the connector out.

    • Do not pull up.

    • Open the display and press the power button for five seconds to drain any remaining charge from the system.

  7. Remove the four 3 mm Phillips #0 screws located on each corner of the battery. Remove the four 3 mm Phillips #0 screws located on each corner of the battery.
    • Remove the four 3 mm Phillips #0 screws located on each corner of the battery.

  8. Pull the battery cable connector towards the battery to disconnect it from its socket. Do not pull up.
    • Pull the battery cable connector towards the battery to disconnect it from its socket.

    • Do not pull up.

  9. Peel up any tape securing the speaker cables to the battery.
    • Peel up any tape securing the speaker cables to the battery.

    • You do not need to remove the speakers, only the tape, allowing the battery to be removed out under the speaker cables.

  10. Remove the battery.
    • Remove the battery.

  11. Remove the four 3 mm Phillips #1 screws from the trackpad. Remove the four 3 mm Phillips #1 screws from the trackpad.
    • Remove the four 3 mm Phillips #1 screws from the trackpad.

  12. Use tweezers to gently lift the upper-right corner of the track pad.
    • Use tweezers to gently lift the upper-right corner of the track pad.

    • Remove the track pad by slowly pulling it up and away from you.

Sonuç

To reassemble your device, follow these instructions in reverse order.

4 farklı kişi bu kılavuzu tamamladı.

Arvind Krish

Üyelik tarihi: 26-04-2017

179 İtibar

1 Kılavuz yazıldı

Takım

Cal Poly, Team S21-G6, Livingston Spring 2017 Cal Poly, Team S21-G6, Livingston Spring 2017 üyesi

CPSU-LIVINGSTON-S17S21G6

5 Üyeler

24 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 6

Son 7 gün: 41

Son 30 gün: 143

Her zaman: 6,353