Bu sürüm, hatalı düzenlemeler içerebilir. En son doğrulanmış bellek kopyası dönün.
Neye ihtiyacın var
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Turn the device on its screen.
-
Remove the ten 4mm screws using a T8 Torx screwdriver.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Gently flip out support feet located near the bottom of device.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Gently lift the back cover off the device. The back cover should come off easily.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the opening tool's angled edge to lift the clasps securing the screen and motherboard cables.
It’s not necessary to remove the cables. Unclip the white touch cable from the touch board as shown in step 8, then remove the two screws holding the board to the frame, as shown in step 9. The board can then be moved out of the way to lay flat on your work surface without having to disconnect all the cables. Doing this eliminates this step and step 5. The order of operations then would be steps 1-3, 8, 9, 6, 7, and 10.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Disconnect the screen and copper colored motherboard cables and tuck them under the device to prevent future hassle.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the two black 3mm screws from the internal cover with a Phillips 00 screwdriver.
-
Remove the internal cover.
-
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Disconnect the black camera cable and pull it back to prevent future hassle.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the angled edge of the plastic opening tool to lift the clasp securing the touch control board cable.
-
Disconnect the silver and blue touch control board cable.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the two silver 3mm screws holding the touch control board in place with a Phillips 00 screwdriver.
-
Remove the touch control board.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the plastic opening tool's angled edge to remove the black and white wires connected to the wireless WLAN card.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the plastic opening tool's angled edge to pry the black battery cable loose.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the plastic opening tool's angled edge to remove the red and black CMOS battery cable.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the plastic opening tool's angled edge to lift the clasp securing the silver circuit board cable.
-
Pull back the circuit board cable to prevent future hassle.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Use the opening tool's angled edge to remove the CMOS battery.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the eleven black 4mm screws holding the battery in place with a Phillips 00 screwdriver.
-
-
Bu adım çevrilmemiş. Çevrilmesine yardım edin
-
Remove the battery.
-
İptal et: Bu kılavuzu tamamlamadım.
13 farklı kişi bu kılavuzu tamamladı.
9 Yorum
needs the help to repair the Dell XPS18
It all worked good. Thanks.
My unit is missing the right foot stand. Is there anywhere else I can find the model number. Need to purchase a new power supply?
Also might need to replace the touchscreen its cracked. Have to power her up first to find out. Do you have a video for touchscreen replacement?
I did this and now my comp just has a double blinking white light…? and will not turn on.
Mine too, did you manage to find what it was?
Wow! I cannot believe how straight forward this guide is!!! Photos depicting every step. My computer now says “1 hour and 12 min until full charge"!!!! Thank you very much!!!!!
I replaced the battery and still having the same problem. Please help