Ana içeriğe geç

Disassembling Arnova 7K G3 Logic Board Ribbon Connectors

Neye ihtiyacın var

  1. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors, Rear Cover: adım 1, 3 resimden 1. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors, Rear Cover: adım 1, 3 resimden 2. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors, Rear Cover: adım 1, 3 resimden 3.
    • Remove four 5 mm Phillips #00 screws from each corner of the tablet.

  2. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 2, 2 resimden 1. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 2, 2 resimden 2.
    • Place the iFixit opening tool in the notches between the cases and pull the covers apart.

  3. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 3, 1 resimden 1.
    • Repeat step two until 3/4 of the rear cover is unlatched.

    • Proceed to remove the rear cover by gently pulling it apart by hand.

  4. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors, Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 4, 2 resimden 1. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors, Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 4, 2 resimden 2.
    • Peel the copper tape covering the ribbon connector with a set of tweezers.

  5. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 5, 3 resimden 1. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 5, 3 resimden 2. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 5, 3 resimden 3.
    • Locate the two gray pins on the ribbon connector.

    • Grab the first pin with tweezers and gently pull it towards the ribbon. Repeat the step.

    • Gently pull the ribbon cable out of the connection port.

  6. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 6, 3 resimden 1. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 6, 3 resimden 2. Disassembling Arnova 7K G3 Logic Board Ribbon Connectors: adım 6, 3 resimden 3.
    • Locate the ribbon connector two.

    • Locate the pins of ribbon connector two. Repeat step two for unlocking the pins.

    • Gently pull the ribbon out of the connection port.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Kue

Üyelik tarihi: 03/18/15

301 İtibar

3 adet Kılavuz yazıldı

Ekip

Michigan Tech, Team 1-2, Lauer Spring 2015 Michigan Tech, Team 1-2, Lauer Spring 2015 üyesi

MTU-LAUER-S15S1G2

2 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 1

Her zaman: 297