Skip to main content

Giriş

In this guide, you will learn how to disassemble the motor housing cover.

  1. Using a spudger, gently pry off the aluminum drip ring. Using a spudger, gently pry off the aluminum drip ring.
    • Using a spudger, gently pry off the aluminum drip ring.

  2. Using a 1 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.
    • Using a 1 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.

  3. Using a spudger, pry the planetary gear cover from the mixer shaft. Using a spudger, pry the planetary gear cover from the mixer shaft.
    • Using a spudger, pry the planetary gear cover from the mixer shaft.

  4. Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın

    Android Tamir Setleri

    Yeni bir ekran veya pil, bir tamir kiti kadar yakınında.

    Hemen Alışveriş Yapın
  5. Using a flathead screwdriver, remove the five, 28 mm front motor housing screws.
    • Using a flathead screwdriver, remove the five, 28 mm front motor housing screws.

    • Using the same flathead screwdriver, remove the two, 28 mm locking screws.

    • One of the locking screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  6. Turn your device around. Using the same flathead screw driver, remove the two, 28 mm rear locking screws.
    • Turn your device around. Using the same flathead screw driver, remove the two, 28 mm rear locking screws.

    • One of the rear motor housing screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  7. Using a phillips 2 screwdriver, remove the 10 mm screw from top of back cover. The rear cover is now completely free from the mixer.
    • Using a phillips 2 screwdriver, remove the 10 mm screw from top of back cover.

    • The rear cover is now completely free from the mixer.

  8. Carefully pull the power cord from the notch in back of the mixer. The motor housing cover is now completely free from the base of the mixer.
    • Carefully pull the power cord from the notch in back of the mixer.

    • The motor housing cover is now completely free from the base of the mixer.

  9. Lift the motor housing cover from the mixer base.
    • Lift the motor housing cover from the mixer base.

    • Be sure to place the cover upside down to prevent grease from leaking out.

Sonuç

To reassemble your device, follow these instructions in reverse order.

7 farklı kişi bu kılavuzu tamamladı.

Chris Gonzales

Üyelik tarihi: 12-10-2014

845 Reputation

2 adet Kılavuz yazıldı

Team

Cal Poly, Team 14-28, Maness Fall 2014 Cal Poly, Team 14-28, Maness Fall 2014 üyesi

CPSU-MANESS-F14S14G28

4 Üyeler

12 adet Kılavuz yazıldı

8 Comments

Well fine job! Just finished and t works!!!

James Anderson - Yanıt

Instruccion is exelent but I veleave the problem is electric. can you give aidea. dhe machine does’nt work at all

Aristides Aleman - Yanıt

Thank you! I'm repainting my white mixer a deep cherry red gloss to match my kitchen. These mixers can last 20+ years, if you take care of them. But, who wants the same color kitchen for that long? Bonus: saved $50+ by painting it the color I wanted, rather than pay the extra for a mixer from the colored choices.

Heather Schrader - Yanıt

Do the motor housing sometimes become to hard to remove? I followed all the steps yet it still acts as if something inside the housing is keeping it from coming off.

Royce M - Yanıt

Nothing else, only the planetary assembly, and the 9 big housing screws. Once those are off, it can take a lot of jiggling and persistence, mostly because there’s a vacuum between the vertical shaft and the bushing inside. Remember to loosen the cord in case to prevent yanking it accidentally when the cover comes off.

Ariel Cornejo -

Add Comment

View Statistics:

Past 24 Hours: 19

Past 7 Days: 121

Past 30 Days: 527

All Time: 22,325