Ana içeriğe geç

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

Disassembling Ridgid R86034 Housing

Salt Önkoşul
Bu kılavuz yalnızca diğer kılavuzlar için bir ön koşul olarak kullanılmak üzere tasarlanmıştır. Tek başına eksiktir.

Neye ihtiyacın var

  1. Disassembling Ridgid R86034 Housing, Disassembling Ridgid R86034 Housing: adım 1, 1 resimden 1.
    • Use the flat side of a metal spudger to peel the black rubber cover off of the casing.

    • The rubber cover is securely attached to the housing so some force is necessary.

    • When putting the rubber cover back, remember that its orientation is important. Rotate the casing until it fits onto the housing with no gaps between it and the clear cover.

  2. Disassembling Ridgid R86034 Housing: adım 2, 2 resimden 1. Disassembling Ridgid R86034 Housing: adım 2, 2 resimden 2.
    • Remove the plastic cover with your hands. The plastic cover should be much easier to remove than the rubber cover. There is no need to force it off.

  3. Disassembling Ridgid R86034 Housing: adım 3, 3 resimden 1. Disassembling Ridgid R86034 Housing: adım 3, 3 resimden 2. Disassembling Ridgid R86034 Housing: adım 3, 3 resimden 3.
    • Unscrew the four 16 mm long screws from the back panel with a T10 Torx Screwdriver.

    • Use a firm grip to peel the the back panel off. It is sealed tight and requires a good amount of force to remove.

  4. Disassembling Ridgid R86034 Housing: adım 4, 2 resimden 1. Disassembling Ridgid R86034 Housing: adım 4, 2 resimden 2.
    • Unscrew the eight 15 mm T10 Torx screws from the housing

    • The screw hole located nearest the battery port is deep and small. Most screwdrivers with replaceable bits will not fit into the hole. Instead use a conventional screwdriver that fits.

  5. Disassembling Ridgid R86034 Housing: adım 5, 1 resimden 1.
    • Place the driver flat on a table before completely separating the two halves of the housing so components don't fall out during opening.

    • Pry apart the two halves of the housing at the back side of the driver using the metal spudger .

    • The housing is easier to remove if you pry from multiple sides.

  6. Disassembling Ridgid R86034 Housing: adım 6, 2 resimden 1. Disassembling Ridgid R86034 Housing: adım 6, 2 resimden 2.
    • Do not remove the direction switch. It isn't necessary.

    • Pull out all electrical components from housing by hand. First, lift out the motor. Next, follow the wires, lifting out components until all components are outside of the housing.

    • With two exceptions all of the components should come out of their respective slots with ease and require little force to lift out. The circuit board located nearest the battery pack and the LED light will be hard to pull out.

    • When reassembling remember to precisely place all components in their correct slots with their correct orientations.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Nathan Hoyt

Üyelik tarihi: 04/20/15

241 İtibar

2 adet Kılavuz yazıldı

Ekip

Cal Poly, Team 15-5, Amido Spring 2015 Cal Poly, Team 15-5, Amido Spring 2015 üyesi

CPSU-AMIDO-S15S15G5

4 Üyeler

12 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 0

Her zaman: 71