Ana içeriğe geç

Bu kılavuzda güncel değişiklikler var. En son onaylanmamış sürüme geçin.

DualShock 4 Button Flex Board Replacement

Neye ihtiyacın var

  1. DualShock 4 Button Flex Board Replacement, Opening the enclosure: adım 1, 3 resimden 1. DualShock 4 Button Flex Board Replacement, Opening the enclosure: adım 1, 3 resimden 2. DualShock 4 Button Flex Board Replacement, Opening the enclosure: adım 1, 3 resimden 3.
    • Unscrew these 4 PH0 Screws to open the back cover.

    • Carefully pry around the cover with a spudger. Pull the back part to open the enclosure.

    • Be careful not to pull too far though, because there is a fragile connector connecting the light bar assembly.

    • Disconnect the light bar ribbon cable.

  2. DualShock 4 Button Flex Board Replacement, Please note:: adım 2, 1 resimden 1.
    • Note that when opening the case, the following parts might fall off: L2 Trigger, R2 trigger, 2x trigger springs. If they don't, remove them and keep them in a safe place for later.

  3. DualShock 4 Button Flex Board Replacement, Disconnecting cables: adım 3, 2 resimden 1. DualShock 4 Button Flex Board Replacement, Disconnecting cables: adım 3, 2 resimden 2.
    • Disconnect the battery connector and remove the battery.

    • And the touch bar cable. Push the cable carefully through the small hole in the plastic midframe.

  4. DualShock 4 Button Flex Board Replacement, Removing the front cover: adım 4, 3 resimden 1. DualShock 4 Button Flex Board Replacement, Removing the front cover: adım 4, 3 resimden 2. DualShock 4 Button Flex Board Replacement, Removing the front cover: adım 4, 3 resimden 3.
    • Remove the lonely, PH1 screw holding the motherboard and the midframe.

    • Remove the front cover from the midframe. If it gets stuck, you may need to jiggle the joysticks.

  5. DualShock 4 Button Flex Board Replacement, Removing the button board- Part 1: adım 5, 3 resimden 1. DualShock 4 Button Flex Board Replacement, Removing the button board- Part 1: adım 5, 3 resimden 2. DualShock 4 Button Flex Board Replacement, Removing the button board- Part 1: adım 5, 3 resimden 3.
    • Starting from the bottom, carefully remove the board from these 4 latches. It might also get caught on the bottom of the speaker grille.

    • Then, remove the bumper buttons and the contact pads for them and the triggers.

    • The top of your controller should now look like pic. 3 Then, unlatch the board from there as well

    • To be continued...

  6. DualShock 4 Button Flex Board Replacement, Removing the button board- part 2: adım 6, 3 resimden 1. DualShock 4 Button Flex Board Replacement, Removing the button board- part 2: adım 6, 3 resimden 2. DualShock 4 Button Flex Board Replacement, Removing the button board- part 2: adım 6, 3 resimden 3.
    • Now that your controller looks something like pic 1, open the midframe Partially.

    • Again, be careful here, because the vibration motors are hard-soldered on the board.

    • Remove the two more latches on the sides of the contact pins.

    • Pull the board out carefully.

  7. DualShock 4 Button Flex Board Replacement, That's it! Well... Kinda: adım 7, 1 resimden 1.
    • Get your new button board and follow the steps in reverse order to reassemble your device. If you need help re installing the trigger buttons (trust me, it is hard to do so) follow this guide: PS4 Dualshock 4 trigger reassembly

Sonuç

To reassemble your device, follow this guide: PS4 Dualshock 4 trigger reassembly

11 farklı kişi bu kılavuzu tamamladı.

Devnol

Üyelik tarihi: 12/01/18

2.648 İtibar

5 adet Kılavuz yazıldı

9 Yorum

I’ve changed two flex boards from two different sellers, and I keep having a battery drain of about 25mA after i installed them. The battery drain is not present with the original flex board, any ideas?

Alessandro - Yanıt

Ok no, little update. the battery drain is present even if I disconnect the flex board, the touch connector and the led . It’s something on the main board I think, but I can’t figure out what is it. Is there some insulation that I may have lost when changing the flex board the first time?

Alessandro -

That sounds really weird. I don’t remember any insulation on this specific model of controller. I don’t have this anymore as it was a repair for a friend and I also hadn’t noticed or measured such a drain.

Devnol -

The only other thing I can think of is a failure on one of the components soldered on the main board, but 20mA in standby condition are VERY high!

Alessandro - Yanıt

The warning regarding the rumblers being hard soldered and the wiring is delicate honestly should be in step 4, jiggling joysticks to remove the front cover can easily cause the rumblers to be disconnected and require some time consuming resoldering to reattach them.

sefog - Yanıt

Good point! From the fact that I used the word "again" in step 6, I may have had that in at some point but something happened and I accidentally removed it. I'll add it back. Thanks a lot for the feedback!

Devnol -

As of March 14, 2023, this guide has been updated! Comments regarding step procedures may no longer be relevant.

Clay Eickemeyer - Yanıt

Buenos días. En mi caso cambie el flex, cambie las gomitas conductoras y así y todo sigue sin funcionar el R2. Sabrán cuál es el problema???

Andres Juan Arana - Yanıt

Hi! I'm sorry your R2 button doesn't work. You have some options. 1) Look for damage on the silicone button pad. Make sure the R2 button can push the pad onto the button circuit membrane. Look for damage that prevents the button from pressing. 2) Clean the silicone pad where it touches the button circuit membrane. Dirt or dust might block the connection. 3) Follow the connection on the button circuit membrane to where it connects to the motherboard. Clean the contact on the motherboard and look for electrical damage.

If you have more questions, ask the community!

Good luck!

Clay Eickemeyer -

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 18

Son 7 gün: 107

Son 30 gün: 410

Her zaman: 25,647