Eşyalarını Tamir Et Topluluk Mağaza

Dyson DC58 Main Body Replacement

Giriş

If your Dyson motor is no longer functioning correctly, grab a pair of long tweezers and check out this guide to replace the main body,

Neye ihtiyacın var

Videoya Genel Bakış

  1. Dyson DC58 Main Body Replacement, Bin: adım 1, 1 resimden 1.

    • Make sure your vacuum is unplugged.

    • Avoid pressing the red trigger on the vacuum handle; this will power on the vacuum.

    Düzenle

  2. Dyson DC58 Main Body Replacement: adım 2, 1 resimden 1.

    • Locate the red lever parallel to the red trigger and on the side of the clear bin.

    Düzenle

  3. Dyson DC58 Main Body Replacement: adım 3, 1 resimden 1.

    • Push the red lever downward to open the clear bin. You may need to do this over a trash bin if there is debris in the clear bin.

    Düzenle

  5. Dyson DC58 Main Body Replacement: adım 4, 2 resimden 1. Dyson DC58 Main Body Replacement: adım 4, 2 resimden 2.

    • Push the red lever downward again while pulling the clear bin away from the main body of the Dyson vacuum.

    Düzenle

  6. Dyson DC58 Main Body Replacement, Main Body: adım 5, 1 resimden 1.

    • Flip the vacuum over so that the silver cyclone part of the vacuum is now at the base.

    Düzenle

  7. Dyson DC58 Main Body Replacement: adım 6, 2 resimden 1. Dyson DC58 Main Body Replacement: adım 6, 2 resimden 2.

    • Locate the two visible white clips seen between the main body and the purple cyclone of the vacuum.

    • Use tweezers to pinch the two visible white clips together.

    • It may require a few tries to pinch the clips since the space between the main body and cyclone is small.

    Düzenle

  8. Dyson DC58 Main Body Replacement: adım 7, 1 resimden 1.

    • Tilt and pull the main body away from the purple cyclone of the vacuum.

    • You may hear a loud snap when the cyclone is released from the main body, this is to be expected.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

12 farklı kişi bu kılavuzu tamamladı.

Yazar

6 tane daha katılımcı ile

Krista St Onge

Üyelik tarihi: 09/17/15

2.188 İtibar

2 adet Kılavuz yazıldı

Rozetler: 19

+16 tane daha rozet

Ekip

CSU Fullerton, Team 2-4, Bruce Fall 2015 CSU Fullerton, Team 2-4, Bruce Fall 2015 üyesi

CSUF-BRUCE-F15S2G4

4 Üyeler

19 adet Kılavuz yazıldı

4 Yorum

Mine ended up dismantled after it had been dropped. Couldn't get it back together until I read the bit about the tweezers /(pliers) and the white clips. It does not push in with out squeezing them first

Jason - Yanıt

Has anyone replaced the red release catch?

chrisashton1 - Yanıt

The white C-ring with clips must be pushed down in order to reassemble device. Takes some time to practice.

Anton Simonov - Yanıt

I'm trying to figure out how to put spring and plastic pieces back in on the inside of red lever on motor body?? Any help I'd really appreciate ?

t_picano - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 1

Son 7 gün: 13

Son 30 gün: 51

Her zaman: 12,928