Ana içeriğe geç

Eşyalarını Tamir Et

Onarma Hakkı

Mağaza

Giriş

The Ecovacs Deebot 900 is an autonomous vacuuming robot. If the vacuum motor is not working, the Deebot will not pick up debris and will be unable to clean. Use this guide to replace the vacuum motor of your Ecovacs Deebot 900.

  1. Remove all the brushes from the Deebot.
    • Remove all the brushes from the Deebot.

  2. Using a Phillips #0 screwdriver, remove the two 12.25 mm  screws holding the battery cover in place.​
    • Using a Phillips #0 screwdriver, remove the two 12.25 mm screws holding the battery cover in place.​

  3. Remove the battery cover.
    • Remove the battery cover.

  4. Using the two white straps on the sides of the battery, gently remove the battery. ​
    • Using the two white straps on the sides of the battery, gently remove the battery. ​

    • Be careful not to rip out the battery cable.

  5. Carefully disconnect the battery cable by pulling near the connector at the bottom of the battery compartment.
    • Carefully disconnect the battery cable by pulling near the connector at the bottom of the battery compartment.

  6. Using a Phillips #00 screwdriver, remove the eight screws on the bottom edge of the bumper. ​ Using a Phillips #00 screwdriver, remove the eight screws on the bottom edge of the bumper. ​
    • Using a Phillips #00 screwdriver, remove the eight screws on the bottom edge of the bumper. ​

  7. Remove the black strip on the bottom of the bumper.
    • Remove the black strip on the bottom of the bumper.

  8. Carefully lift up the bumper untill it pops out of place.​ Carefully lift up the bumper untill it pops out of place.​
    • Carefully lift up the bumper untill it pops out of place.​

  9. Disconnect the two cables connecting the bumper to the body of the Deebot. Remove the front bumper from the device.
    • Disconnect the two cables connecting the bumper to the body of the Deebot.

    • Remove the front bumper from the device.

  10. Using a Phillips #00 screwdriver, take out the six screws around the perimeter of the bottom case. Using a Phillips #00 screwdriver, take out the six screws around the perimeter of the bottom case.
    • Using a Phillips #00 screwdriver, take out the six screws around the perimeter of the bottom case.

  11. Insert a Jimmy into the seam and work all the way around the robot. Disconnect the two cables and remove the bottom case from the device.
    • Insert a Jimmy into the seam and work all the way around the robot.

    • Disconnect the two cables and remove the bottom case from the device.

  12. Using the Phillips #00 screwdriver, remove the three screws around the laser unit.
    • Using the Phillips #00 screwdriver, remove the three screws around the laser unit.

  13. Carefully lift the laser unit off of the motor assembly​. Carefully lift the laser unit off of the motor assembly​.
    • Carefully lift the laser unit off of the motor assembly​.

  14. Remove the single screw holding the motor assembly in place using the Phillips #00 screwdriver.
    • Remove the single screw holding the motor assembly in place using the Phillips #00 screwdriver.

  15. Disconnect the ribbon cable holding the assembly in place. Be careful not to damage the cable.
    • Disconnect the ribbon cable holding the assembly in place.

    • Be careful not to damage the cable.

  16. Lift and remove the motor assembly out of the Deebot.​
    • Lift and remove the motor assembly out of the Deebot.​

Sonuç

To reassemble your device, follow these instructions in reverse order.

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 4

Son 7 gün: 45

Son 30 gün: 177

Her zaman: 1,218