Eşyalarını Tamir Et Topluluk Mağaza

Flip Video Ultra Power button Replacement

Giriş

This guide will walk you through on how to remove the power button and replace it. You will need the iFixit Opening Tool and the Phillips #1 Screwdriver. It should take no more than 15 minutes, if it takes more than that then you may have done something wrong.

Neye ihtiyacın var

  1. Flip Video Ultra Power button Replacement, Power button: adım 1, 1 resimden 1.

    • Unlock the battery cover by sliding the switch to the unlock position.

    Düzenle

  2. Flip Video Ultra Power button Replacement: adım 2, 1 resimden 1.

    • Remove the battery cover by sliding it down the camera.

    Düzenle

  3. Flip Video Ultra Power button Replacement: adım 3, 1 resimden 1.

    • Remove the batteries

    Düzenle

  4. Flip Video Ultra Power button Replacement: adım 4, 1 resimden 1.

    • Slide the black upper casing off from the device.

    Düzenle

  5. Flip Video Ultra Power button Replacement: adım 5, 2 resimden 1. Flip Video Ultra Power button Replacement: adım 5, 2 resimden 2.

    • Remove the six 1mm screws from the back and upper casing with the Phillips Head screwdriver.

    Düzenle

  7. Flip Video Ultra Power button Replacement: adım 6, 1 resimden 1.

    • Remove the top casing from the bottom to reveal the inner circuit board.

    Düzenle

  8. Flip Video Ultra Power button Replacement: adım 7, 2 resimden 1. Flip Video Ultra Power button Replacement: adım 7, 2 resimden 2.

    • When removing the back panel, the rubber buttons will become loose and likely fall off the board. This is normal and can easily placed back on the board once finished.

    • Remove the six 1mm screws with the 1 Phillips head screwdriver.

    Düzenle

  9. Flip Video Ultra Power button Replacement: adım 8, 1 resimden 1.

    • Gently separate the circuit board from the casing.

    Düzenle

  10. Flip Video Ultra Power button Replacement: adım 9, 2 resimden 1. Flip Video Ultra Power button Replacement: adım 9, 2 resimden 2.

    • Unscrew the single 1mm screw from USB housing unit.

    Düzenle

  11. Flip Video Ultra Power button Replacement: adım 10, 2 resimden 1. Flip Video Ultra Power button Replacement: adım 10, 2 resimden 2.

    • Unscrew the 2 1mm screws and gently separate camera wires from plastic casing.

    Düzenle

  12. Flip Video Ultra Power button Replacement: adım 11, 1 resimden 1.

    • Gently pry out the USB housing unit with the Ifxit Opening Tool.

    Düzenle

  13. Flip Video Ultra Power button Replacement: adım 12, 3 resimden 1. Flip Video Ultra Power button Replacement: adım 12, 3 resimden 2. Flip Video Ultra Power button Replacement: adım 12, 3 resimden 3.

    • Remove the two 1mm screws and separate the circuit board and camera from the plastic casing.

    Düzenle

  14. Flip Video Ultra Power button Replacement: adım 13, 1 resimden 1.

    • Unscrew the camera housing unit from the plastic case.

    Düzenle
Sonuç

To reassemble your device, follow these instructions in reverse order.

Yazar

2 tane daha katılımcı ile

Nathaniel Ruf

Üyelik tarihi: 10/18/16

514 İtibar

5 adet Kılavuz yazıldı

Rozetler: 5

+2 tane daha rozet

Ekip

UMass Dartmouth, Team 5-7, Martin Fall 2016 UMass Dartmouth, Team 5-7, Martin Fall 2016 üyesi

UMASSD-MARTIN-F16S5G7

3 Üyeler

10 adet Kılavuz yazıldı

0 Yorum

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 1

Son 30 gün: 4

Her zaman: 441