Ana içeriğe geç

Fugoo Tough XL Bass Speaker Replacement

Neye ihtiyacın var

  1. Fugoo Tough XL Bass Speaker Replacement, Case: adım 1, 1 resimden 1.
    • Remove four 3 mm screws using a 3 mm Hex screwdriver.

  2. Fugoo Tough XL Bass Speaker Replacement: adım 2, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 2, 2 resimden 2.
    • Gently remove the outer casing.

    • It should be relatively easy to pull apart, but in the case that it is not easy, don't be afraid to apply the necessary force to pull them apart.

  3. Fugoo Tough XL Bass Speaker Replacement: adım 3, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 3, 2 resimden 2.
    • Pull the device from the external case.

    • Remove four 12 mm screws using a T10 Torx screwdriver.

    • Remove eight 6 mm screws using a T10 Torx screwdriver.

  4. Fugoo Tough XL Bass Speaker Replacement: adım 4, 3 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 4, 3 resimden 2. Fugoo Tough XL Bass Speaker Replacement: adım 4, 3 resimden 3.
    • Use your hands to gently remove the side plates.

    • Use the plastic opening tool to pry off the back plate.

    • It is best to work on the side with the Fugoo trademark.

  5. Fugoo Tough XL Bass Speaker Replacement: adım 5, 1 resimden 1.
    • Slowly pull the front casing from the back casing. If possible, try to avoid putting any tension on the connected cables.

    • Separate the two at a slow, consistent pace to avoid damaging the speaker cables.

  6. Fugoo Tough XL Bass Speaker Replacement, Motherboard: adım 6, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement, Motherboard: adım 6, 2 resimden 2.
    • Carefully untangle the wires that connect the speaker to the motherboard.

  7. Fugoo Tough XL Bass Speaker Replacement: adım 7, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 7, 2 resimden 2.
    • Use tweezers to remove the two ribbon wires on the left and right side of motherboard.

    • Do not pull the cables by the cord, as this could damage the cables and the motherboard. It is best to always disconnect the cables from the base, which is closest to the motherboard, using an iFixit opening tool.

    Theres a second smaller ribbon cable on the underside of the board on the left in my model, for a total of *3* ribbon cables that need to be disconnected.

    Rob B - Yanıt

  8. Fugoo Tough XL Bass Speaker Replacement: adım 8, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 8, 2 resimden 2.
    • Pull the motherboard halfway out.

    • Gently unplug the ribbon using the tweezers.

    • There is a hidden ribbon on the motherboard, that becomes visible once the motherboard has been pulled out.

    Does the motherboard have the charging port on it

    grantierben - Yanıt

  9. Fugoo Tough XL Bass Speaker Replacement: adım 9, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 9, 2 resimden 2.
    • Remove the motherboard and battery.

    • Remove four 3 mm screws from the motherboard using a 3 mm Hex screwdriver.

  10. Fugoo Tough XL Bass Speaker Replacement, Bass Speaker: adım 10, 1 resimden 1.
    • Remove four 3 mm screws using a 3 mm Hex screwdriver.

  11. Fugoo Tough XL Bass Speaker Replacement: adım 11, 2 resimden 1. Fugoo Tough XL Bass Speaker Replacement: adım 11, 2 resimden 2.
    • Pull the bass speaker from the internal case.

Sonuç

To reassemble your device, follow these instructions in reverse order.

Austin Coats

Üyelik tarihi: 02/17/17

107 İtibar

1 Kılavuz yazıldı

Ekip

USF Tampa, Team S19-G1, Hoffman Spring 2017 USF Tampa, Team S19-G1, Hoffman Spring 2017 üyesi

USFT-HOFFMAN-S17S19G1

4 Üyeler

5 adet Kılavuz yazıldı

Bir Yorum

Hello, what is the power of this loudspeaker for resistances Ω, and RMS

Marcin Kopera - Yanıt

Yorum Ekle

İstatistikleri Görüntüle:

Son 24 Saat: 0

Son 7 gün: 0

Son 30 gün: 2

Her zaman: 763